Contact Us

TPS628438YKAR

Brand: Texas Instruments
Texas Instruments TPS628438YKAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS628438YKAR — Power Management & Signal Chain | Superb Automation

TPS628438YKAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS628438YKAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS628438YKAR 600 mA buck with 275 nA quiescent current

The TPS628438YKAR is a member of the TPS62843 family, a step down converter that runs from 1.8 V to 5.5 V, delivers up to 600 mA and regulates an output between 0.4 V and 3.6 V. The operating quiescent current is 275 nA typical in power save mode and the shutdown current is 4 nA typical, which is the number that matters in a wearable that spends its life asleep and wakes for a few milliseconds at a time. The body is the six pin YKA chip scale package, and the output is selected by a single resistor from the VSET pin rather than by a divider.

The converter switches at 1.5 MHz and changes to a no ripple 100 per cent mode when the input falls near the output, which keeps the output clean for a radio or an analogue front end at the end of a battery discharge. The undervoltage lockout sits at 1.75 V rising and 1.65 V falling, so a single cell lithium battery at 3.0 V has a wide margin and a two cell alkaline pack at 2.4 V still runs. The on resistance of the high side switch is 170 milliohm typical and 260 milliohm maximum with the switch node at 3.3 V.

Soft start is not one value across the family. The 436 member ramps in 0.45 to 0.6 milliseconds, the 437 in 0.7 to 1.0 milliseconds, and this 438 member in 1.0 to 1.4 milliseconds, which is the version to take when the load has a large input capacitance and the rail must not be pulled down at power up. All three share the document, the pinout and the VSET scheme, so the ramp is the reason to choose between them rather than any change in the power stage.

Key parameters from the SLVSFU8C document

Input range1.8 V to 5.5 V, UVLO 1.75 V rising and 1.65 V falling
Output range0.4 V to 3.6 V, set by a resistor on the VSET pin
Output current600 mA rated
Switching frequency1.5 MHz, with automatic entry into a no ripple 100 per cent mode
Quiescent current275 nA typical in power save mode with no load
Shutdown current4 nA typical and 850 nA maximum with the enable low
High side resistance170 milliohm typical and 260 milliohm maximum with the switch node at 3.3 V
Soft start1.0 to 1.4 milliseconds on this member, 0.45 to 0.6 on the 436 and 0.7 to 1.0 on the 437
EnableThreshold 0.8 V, internal pull down on the enable pin
AccuracyOutput tolerance quoted over minus 40 to plus 125 degrees junction
Applications in the documentWearables, headsets and earbuds, mobile phones, medical sensor patches and hearing instruments
PackageYKA chip scale body with six pins

Why the shutdown current is the specification that matters

A wearable spends most of its time in a state where the converter is off and only a real time clock, a sensor interrupt and a small memory retention domain are alive. At 4 nA of shutdown current the converter is not part of that budget at all: a 40 milliampere hour coin cell self discharges faster than the part leaks. Once the converter is out of the picture, the next largest leak becomes the deciding term, which is usually a pull up resistor or a supervisor, and those are the parts to attack next.

The 275 nA operating current is the number for the sleeping but enabled state, when the output is regulated and the load draws microamps. That is the state a product sits in between measurements, and 275 nA is low enough that a 3.6 V to 1.8 V rail can stay alive for years on a coin cell. In 100 per cent mode the part stops switching and behaves like a pass element, which removes the switching ripple entirely and is why the document describes the output as no ripple in that mode.

The VSET resistor is the one component that has to be right. It is converted once at start up into one of the internal settings, so a resistor with a wide tolerance can select the neighbouring step, and the output becomes tens of millivolts off with no fault indication. A 1 per cent resistor is the correct choice, and it should be placed close to the pin so that the conversion is not affected by noise at power up.

Where this part fits

Hearing instruments, medical sensor patches, smart jewellery, wireless earbuds and any product where a 600 mA rail has to hold 1.8 V or 3.3 V while the battery drains from 4.2 V to 2.0 V. Our cross reference notes for the family are at power management cross reference and the substitution check we run is at how to verify a drop in replacement.

What to check before a purchase order

Check the member number, not the family. The 436, 437 and 438 share one body and one pinout and differ in the soft start ramp and the output window, so a reel ordered by family name can arrive with a part that ramps four times faster than the board was signed off for. The order code carries the member number and the packing label is the place to read it.

Check the input capacitor against the 1.5 MHz carrier and check the VSET resistor tolerance. Both are small parts that decide whether the rail comes up clean at the first power on, and both are cheaper to check at receipt than to debug on a finished product. The receipt check we run on these reels is at incoming inspection plan.

Questions that come up on this part

Can the output be set to 0.9 V for a core rail, is a common question. The family covers 0.4 V to 3.6 V and this member covers a window inside that range, so the exact setting has to be read from the voltage table for the 438 rather than assumed from the family range. A board that needs a rail outside the window takes another member of the same family and the same footprint.

The second question is whether the 600 mA rating holds to 85 degrees ambient. It does electrically, but the six pin chip scale body has very little copper for heat, and 600 mA at 3.6 V to 1.8 V dissipates more than 300 milliwatt in the converter. A sealed product has to be checked at the enclosure temperature with the copper that the board actually has, not on an open bench.