TPS62841DGRR
Product Specifications
TPS62841DGRR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62841DGRR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62841DGRR: a 750 mA step-down for a 1.8 V to 6.5 V rail
TPS62841DGRR is the HVSSOP member of the TPS6284x step-down family. It takes 1.8 V to 6.5 V in and holds a fixed output between 0.8 V and 1.55 V that is chosen at start-up by one resistor, so a single reel can serve several rails on the same board. The switch current is rated for 750 mA of output, which is enough for a sensor hub, a radio module or a small display backlight sitting on a two cell alkaline or a single Li-SOCl2 pack.
The DGR tail is the body most people skip past when they compare this family, and that is a mistake. It is the only member with an exposed pad, 3 mm by 5 mm of HVSSOP plastic with a thermal land under the die, and that land is what keeps a 750 mA converter honest inside a sealed enclosure. The other two bodies, the 1.5 mm by 2 mm VSON and the 0.97 mm by 1.47 mm WCSP, are smaller but they get rid of heat through the pins alone.
The numbers on this page come from SLVSEC6D, revised March 2020, and from the package option addendum at the back of that document. They are the values we check a customer BOM against before we quote: the quiescent current at light load, the 1.8 MHz switching frequency that keeps the inductor at 2.2 microhenry, the resistor window on the VSET pin, and the 2500 piece reel that the DGR tail is packed on.
What the order code sits on
| Function | synchronous step-down converter with integrated switches |
| Input range | 1.8 V to 6.5 V on VIN, 7 V absolute maximum |
| Output range | 0.8 V to 1.55 V in 50 mV steps, 16 settings by resistor |
| Output current | 750 mA |
| Quiescent current | 80 nA typical at 1.2 V out with no load, 60 nA at 1.8 V out |
| Duty cycle mode | 100 percent mode holds 120 nA typical when the input falls to the output |
| Shutdown current | 25 nA typical, 300 nA maximum over the full temperature window |
| Switching frequency | 1.8 MHz nominal, DCS-Control loop |
| Light load behaviour | automatic PFM and PWM transition, MODE pin forces PWM |
| Switch current limit | 1.0 A minimum, 1.2 A typical, 1.4 A maximum on the high side |
| Soft start limit | 0.15 A to 0.3 A, so inrush stays inside a coin cell budget |
| Output discharge | 35 mA typical sink on VOS when EN goes low |
| Undervoltage lockout | 1.72 V to 1.8 V rising, 1.45 V to 1.75 V falling |
| Package | HVSSOP-8, 3 mm by 5 mm, PowerPAD thermal land, 9 lands in total |
| Thermal resistance | 58.1 degrees per watt junction to ambient on the JEDEC board |
| ESD | plus or minus 2000 V human body, plus or minus 500 V charged device |
| Junction range | minus 40 to 125 degrees operating, 150 degrees absolute maximum |
| Carrier | 2500 pieces on a large reel, marking T841R, SnAgCu finish |
| Moisture level | level 1 at 260 degrees, unlimited floor life |
The HVSSOP body and its exposed pad
Pin 9 of the DGR body is the thermal pad, and the data sheet is direct about it: the PowerPAD must be connected to GND. That single sentence decides how the part behaves in a real build. The pad is the lowest impedance path from the die to the copper, and it is also the return path for the high side switch, so a pad that is left floating or tied to a quiet ground with a long trace produces both a thermal problem and a switching noise problem at the same time.
The pad also changes what the assembler has to do. A HVSSOP with an exposed pad needs a stencil aperture that controls paste volume, otherwise the die sits on a pillar of solder and the pins lift. The TI package drawing for this body prints the recommended stencil openings for 0.1 mm, 0.125 mm and 0.15 mm foils, with a 1.35 mm by 1.65 mm opening at the 0.125 mm thickness, and it asks for 100 percent paste coverage by area. When we build this body we check the aperture against the foil thickness on the paste screen before the first article, because a stencil built for a plain SOIC will not transfer the right volume into that opening.
The rewarded number is 58.1 degrees per watt. At 3.6 V in and 1.2 V out with 750 mA, the converter loses roughly 0.15 W, and that loss lifts the junction about 9 degrees above the board around it. Without the pad, on the same copper, the figure is closer to 105 degrees per watt in the small VSON body, which is why a sealed box with no airflow is the case where the DGR is worth its extra 3 mm of board length.
Choosing the output with one resistor
The output voltage is read once, during the start-up delay, by a resistor to digital converter on the VSET pin. After the value is latched the converter switches the R2D block off, so no current flows through the resistor in normal operation. Two details decide whether the setting lands where the drawing expects it: the resistor has to come from the E96 series and sit inside the window printed in the table below, and the parasitic capacitance from VSET to ground has to stay under 100 pF. A long trace to a test point or a probe pad is enough to push a false reading, and the symptom is a rail that comes up at the neighbouring step, not at the value on the drawing.
| 0.8 V | VSET tied to GND, no resistor |
| 0.85 V | 0.909 k, window 0.87 k to 0.95 k |
| 0.9 V | 1.74 k, window 1.67 k to 1.81 k |
| 0.95 V | 2.87 k, window 2.76 k to 2.98 k |
| 1.0 V | 4.32 k, window 4.15 k to 4.49 k |
| 1.05 V | 6.04 k, window 5.80 k to 6.28 k |
| 1.1 V | 8.45 k, window 8.11 k to 8.79 k |
| 1.15 V | 11.5 k, window 11.04 k to 11.96 k |
| 1.2 V | 15.8 k, window 15.17 k to 16.43 k |
| 1.25 V | 21.5 k, window 20.64 k to 22.36 k |
| 1.3 V | 28.7 k, window 27.55 k to 29.85 k |
| 1.35 V | 38.3 k, window 36.77 k to 39.83 k |
| 1.4 V | 52.3 k, window 50.21 k to 54.39 k |
| 1.45 V | 71.5 k, window 68.64 k to 74.36 k |
| 1.5 V | 102 k, window 97.92 k to 106.08 k |
| 1.55 V | 267 k, window 256.32 k to 277.68 k |
The resistor tolerance is specified at 1 percent and the temperature coefficient at plus or minus 200 parts per million per degree, which is why the windows in the table are wide enough for a standard 1 percent part but not wide enough for a 5 percent carbon film. The step from 1.5 V to 1.55 V jumps from 102 k to 267 k, so a board that needs 1.55 V cannot use a resistor left over from a 1.5 V build and adjust it by trimming.
What the quiescent current buys at the battery
The headline figure of the family is the no-load input current while the converter is still switching: 80 nA typical with a 1.2 V output and 60 nA with 1.8 V out. On a 100 mAh coin cell, 80 nA drawn continuously would empty the cell in about 142 years if nothing else were connected. The real number is much smaller than the load current, so the converter is not the item that decides the service life of a metering node. What matters is that it does not add a milliampere of standing loss, which is what a general purpose buck with a 20 microamp quiescent current would do.
Two other states matter for a battery product. When the input falls to the output the converter goes to 100 percent duty cycle, keeps the high side switch on and holds 120 nA typical, with the output set point raised by 30 mV to give the loop room. And when EN is pulled low the part draws 25 nA typical, 300 nA maximum, so a product that sits in storage for a year does not come back with a flat cell.
The weak point of the family in a battery product is the light load efficiency curve, not the quiescent current. The data sheet gives 80 percent efficiency at 1 microamp of load with 3.6 V in and 1.8 V out, which is a good number but still a loss, so a wake-up duty cycle that runs the converter for a few milliseconds every second can cost more than the sleep current does. When we look at a customer's power budget we ask for the average load, not the peak, because the average is what the 80 nA figure is measured against.
Where this body fits in a build
The applications printed in the data sheet are smart meters, smart thermostats, asset trackers, wearables, medical sensor patches and patient monitors, industrial IoT nodes including NB-IoT, test and measurement, and equipment that has to survive an ATEX or intrinsic safety review. The common thread is a rail that has to stay alive for years and a load that is measured in milliamps for a few seconds at a time. The DGR body adds the cases where the board sits in a potted housing or a sealed meter can, because that is where the thermal pad earns its area.
For a project that is buying this part against a lead time problem, the sourcing route matters as much as the electrical one. Our component lead time page covers how we hold a buffer on the parts that sit on a long allocation, and the power management cross reference covers the pin level comparison against the other members of the family, including the two bodies that are not drop in replacements for this one.
Questions from purchasing and from the line
Is the DGR tail the same die as the DLC tail? Yes. The device comparison table prints the same 750 mA output, the same 0.8 V to 1.55 V window and the same 16 settings for TPS62841DLC, TPS62841YBG and TPS62841DGR. What changes is the body, the pin count, the thermal path and the carrier.
Can a DLC part be used where the board has a DGR footprint? No. The DGR land pattern is 3 mm by 5 mm with an exposed pad, the DLC pattern is 1.5 mm by 2 mm with no pad, and the pin order is different: VOS is pin 1 on the DGR and pin 8 on the DLC. Only the electrical function is shared.
Does the part need a feed forward capacitor? No. The regulation loop is internally compensated and the data sheet lists one inductor, one input capacitor, one output capacitor and the VSET resistor as the complete external set for the typical application.
What reel does the R tail come on? 2500 pieces on a large reel, marking T841R, SnAgCu finish, moisture level 1 at 260 degrees. A prototype line that needs 100 pieces is buying a partial reel, not a different part number, and the cut tape has to be re-reeled and re-labelled by the distributor if the line cannot accept a partial reel with an opened moisture barrier.
What is the STOP pin situation? The DGR body does not have one. Pin 7 is not connected internally and the data sheet says so directly, so a board that needs the quiet measurement window has to use the DLC body or hold the rail with an external load switch.