TPS62840DLCR
Product Specifications
TPS62840DLCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62840DLCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62840DLCR 750 mA buck with a 60 nA quiescent current
The TPS62840DLCR is the SON-8 member of the TPS6284x line, a step down converter that runs from 1.8 V to 6.5 V and delivers up to 750 mA with an operating quiescent current of 60 nA typical with no load and the device switching. The output is not set by a divider: a resistor from the VSET pin selects one of sixteen internal settings, 1.8 V to 3.3 V in 100 mV steps on the DLC body, which is what makes a 60 nA figure possible at all, because an external divider would draw more than the converter itself.
The family is built around the end of a battery life. In 100 per cent duty mode the quiescent current is 120 nA, the part stops switching and passes the input to the output through the high side switch, and the output is set slightly below the input by the resistive drop. A product that runs on a primary cell or a lithium coin cell spends most of its life in that mode, and the difference between 60 nA and 1 microamp is the difference between a ten year battery and a three year battery.
The switch resistances are modest, which is the price of the quiescent current. In the DLC and YBG bodies the high side is 430 milliohm typical and 600 milliohm maximum at 3.6 V input with a 200 mA test current, 340 milliohm and 465 milliohm at 5 V, and the low side is 170 milliohm and 240 milliohm at 3.6 V, 135 milliohm and 180 milliohm at 5 V. The DGR body is higher still, 460 and 630 milliohm on the high side, 200 and 270 milliohm on the low side. A 750 mA rating with those resistances is honest only at low duty cycles or with a low output voltage.
Key parameters from the SLVSEC6D document
| Input range | 1.8 V to 6.5 V, UVLO rising 1.72 V to 1.8 V and falling around 1.45 V |
| Output | Sixteen internal settings selected by a resistor on VSET, 1.8 V to 3.3 V in 100 mV steps on the DLC body |
| Output current | 750 mA rated |
| Switching frequency | 1.8 MHz typical, with a 100 per cent duty mode at the bottom of the input range |
| Quiescent current | 60 nA with no load and switching, 120 nA in 100 per cent mode |
| Shutdown current | 25 nA typical and 300 nA maximum |
| High side resistance | 430 milliohm typical and 600 milliohm maximum at 3.6 V, 340 and 465 milliohm at 5 V in the DLC body |
| Low side resistance | 170 milliohm typical and 240 milliohm maximum at 3.6 V, 135 and 180 milliohm at 5 V |
| Control pins | EN and STOP, both with an internal 200 to 450 kiloohm pull down, plus MODE for forced PWM |
| Soft start | Internal ramp, with the STOP pin holding the output in a defined state |
| Current limit | Switch current limit with a soft start ramp value of 0.15 A to 0.3 A |
| Package | SON-8 DLC body, with WCSP-6 and HVSSOP-8 siblings in the same family |
What the nanoamp class changes on a board
At 60 nA the converter is no longer the dominant load in a sleeping product, and the next largest leak becomes the deciding term: a supervisor, a pull up on an open drain signal, a charged capacitor leaking through a reverse biased diode. That is why the family carries a STOP pin. Driving STOP high puts the part into a state where the output is held and the input current is in the nanoamp range, which is the mode a shipping product uses when it has to arrive with a charged battery.
The VSET resistor is worth understanding. The part converts the resistor once at start up into one of sixteen settings, so a resistor that is off by 20 per cent can select the neighbouring step and the output becomes 100 mV off. A 1 per cent resistor in the right place is not optional. The DGR body carries a wider range of settings, 0.8 V to 1.55 V in 50 mV steps for the TPS62841 and 1.8 V to 3.6 V in 100 mV steps for the TPS62842, which is why the same catalogue number can behave differently depending on which body was ordered.
Efficiency at 1 microamp is quoted at 80 per cent for 3.6 V in and 1.8 V out, which sounds impossible until the quiescent current is taken into account: at that load the converter is transferring microwatts and the loss is the quiescent current itself. The figure matters for a product that wakes for a measurement, takes a reading and sleeps again, because the average current is set by the wake time and the quiescent current, not by the peak efficiency.
Where this part fits
Smart meters, utility meters, sensor nodes on coin cells, medical patches, hearing instruments and any product where the sleep current is the specification. The cross reference notes for this family are at power management cross reference and the substitution check is at how to verify a drop in replacement.
What to check before a purchase order
Check the body, not the family name. TPS62840DLC is the SON-8 with the 1.8 V to 3.3 V settings, TPS62840YBG is the WCSP-6, TPS62841DGR is the HVSSOP-8 with the 0.8 V to 1.55 V settings and TPS62842DGR is the HVSSOP-8 with the wider 1.8 V to 3.6 V settings. The same suffix logic does not carry across the bodies, so a quantity ordered from the family name can arrive with a part that cannot reach the rail the board needs.
Check the VSET resistor tolerance and the STOP pin state at power up. Both are cheap to get right and expensive to find on a finished product. The receipt check on the marking and the reel is at incoming inspection plan.
Questions that come up on this part
Is the 750 mA rating available at 1.8 V input, is the first question. At 1.8 V input and 1.8 V output the part is in 100 per cent mode and the current is limited by the high side resistance, 600 milliohm maximum, so 750 mA would drop 450 mV and the output would follow the input down. The 750 mA figure belongs to inputs above about 3 V with a lower output, and the current at the bottom of the range is set by the resistance, not by the rating.
The second question is whether the part can be used as a load switch. In 100 per cent mode it behaves like one, with 120 nA of quiescent current and a 600 milliohm maximum pass element, which is useful when the rail has to be gated without a second component. It is not a substitute for a real load switch on a rail that carries amps, and the current limit of the converter is not a short circuit protection for a downstream fault.