Contact Us

TPS6283810YFPR

Brand: Texas Instruments
Texas Instruments TPS6283810YFPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS6283810YFPR — Power Management & Signal Chain | Superb Automation

TPS6283810YFPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS6283810YFPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS6283810YFPR fixed 1.0 V at 3 A in a 1.2 mm by 0.8 mm WCSP

The TPS6283810YFPR is a fixed 1.0 V synchronous step down converter rated 3 A, in a six bump WCSP of 1.2 mm by 0.8 mm. It runs from 2.4 V to 5.5 V, switches at 3.5 MHz, and uses DCS Control with an automatic transition into power save at light load. The output voltage is fixed inside the package, so the part has six pins, no feedback divider and no external compensation, which is why the whole converter fits under a 1.6 mm by 1.2 mm area including the inductor and the capacitors.

The internal switches are 26 milliohm each, the high side switch current limit window is 3.6 A minimum, 4.3 A typical and 5.0 A maximum, and the output accuracy in PWM is 0.990 V to 1.010 V, which is 1 per cent at 25 degrees. Quiescent current with the enable high and no load is 4 microamp typical and 10 microamp maximum, and the shutdown current is 0.05 microamp typical with 0.5 microamp maximum. Soft start reaches 95 per cent of the nominal output in 1.25 milliseconds.

The 3.5 MHz carrier is the reason the passive parts are small, and also the reason the placement of the input capacitor matters more than the value of the output capacitor. At 3.5 MHz a 470 nanohenry inductor carries the full 3 A with a ripple of about 1 A, so the output capacitor sees a small triangular current and 10 microfarad of ceramic is enough. The price is switching loss, which is why the part is offered with a power save mode that drops the frequency and the quiescent current at light load.

Key parameters from the SLVSEX7 document

Input range2.4 V to 5.5 V
Output1.0 V fixed inside the package, 0.990 V to 1.010 V in PWM mode
Output current3 A rated, with a note that lifetime falls when 3 A is held above 105 degrees junction
Switching frequency3.5 MHz, with power save mode at light load
Switch resistance26 milliohm on each of the two internal switches
Current limitHigh side 3.6 A minimum, 4.3 A typical, 5.0 A maximum
Quiescent current4 microamp typical and 10 microamp maximum, not switching
Shutdown current0.05 microamp typical and 0.5 microamp maximum
Soft start1.25 milliseconds from enable high to 95 per cent of the nominal output
Power goodOpen drain with a window near the nominal output and a 0.4 V low level at 1 mA sink
DischargeInternal output discharge when the enable is low
PackageSix bump WCSP of 1.2 mm by 0.8 mm, thermal shutdown with hysteresis

What a fixed 1.0 V rail is for

A 1.0 V rail is a core supply: an FPGA core, a small application processor, a DDR termination rail or a digital signal processor. Those loads care about accuracy and transient response far more than they care about trimming, and they almost never want a divider on the board. The fixed member removes the divider, which removes two resistors, a noise pickup node and one tolerance term, and it removes the failure mode where a divider is populated for the wrong rail on a build variant.

The transient response is the second reason. DCS Control reacts to the output voltage directly rather than to a ramp, so a 1 A load step at 3.5 MHz is answered within a few switching cycles and the output moves by tens of millivolts with 10 microfarad of output capacitance. A current mode converter with the same passives needs more capacitance or a lower bandwidth and a longer recovery.

The power good pin is a window comparator referenced to the nominal output, with the lower threshold around 96 per cent on the way down and the upper threshold around 107 per cent, and a sink capability of 1 mA with a 0.4 V low level. That is enough to drive a supervisor input or a power sequence gate directly, without a buffer, and it is the reason a small board can sequence four rails with four of these parts and no sequencer chip.

Where this part fits

FPGA and processor core rails on handheld instruments, sensor modules with a digital back end, portable ultrasound probe heads and wearable devices where the total converter area has to stay under 2 mm by 2 mm. Our cross reference notes for the family are at power management cross reference and the substitution check we run is at how to verify a drop in replacement.

What to check before a purchase order

Check that the requested output voltage is the one in the order code. This part is 1.0 V; the same family is offered at other fixed voltages in the same six bump body, and the marking on a WCSP is a two character code that does not read as a voltage. A reel that was ordered by body size alone can deliver 1.2 V or 1.8 V parts, and the board comes up with a core rail that is out of specification with no visible fault.

Check the input capacitor placement before the quantity. At 3.5 MHz the loop from the input capacitor through the high side switch and back to ground carries 3 A pulses, and 2 mm of extra trace is enough to raise the input ripple above the data sheet curve. The receipt and solder check on the WCSP parts we handle is described at incoming inspection plan.

Questions that come up on this part

Can the output be raised to 1.1 V, is a common question. Not without an external circuit, because the divider is inside the package. A board that needs a trimmable core rail takes the adjustable member of the same family or a part with an external feedback pin, and mixing the two on one bill of materials is how a rail ends up at the wrong voltage on a variant.

The other question is whether 3 A is available at 2.5 V input. The current limit holds, but at 2.5 V input with 1.0 V out the duty cycle is 40 per cent and the resistive losses dominate, so the usable current at high ambient is lower than the rating. The vendor states the 3 A lifetime caution above 105 degrees junction for exactly this reason, and a sealed enclosure is where that limit is reached first.