TPS628303ADRLR
Product Specifications
TPS628303ADRLR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS628303ADRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS628303ADRLR 3 A synchronous buck in the SOT583 body
The TPS628303ADRLR is the 3 A member of the TPS62830x family and one of the two members offered in the DRL SOT583 package of 1.6 mm by 2.1 mm. It converts 2.25 V to 5.5 V to an adjustable 0.5 V to 4.5 V, uses the same DCS Control loop and the same 2.0 MHz quasi fixed oscillator as the smaller members, and shares the eight pin pinout inside its own package, so a board that carries the 3 A part can also carry the 4 A part without a change to the copper.
The electrical table is the family table: 500 mV feedback with a 495 mV to 505 mV window, 1 per cent accuracy across minus 40 to plus 125 degrees junction, 35 milliohm typical and 57 milliohm maximum high side at 5 V input, 18 milliohm typical and 29 milliohm maximum low side, 7 nA typical quiescent current and 100 nA typical shutdown current. Soft start runs from 180 to 440 microseconds on the standard options and up to 1300 microseconds on the K options, which is the version to take when a large output capacitor has to be charged without pulling the input rail down.
The SOT583 body is the reason this member exists. A 3 A rail in a leaded body of 1.6 mm by 2.1 mm suits a board that cannot carry a QFN with an exposed pad, or a board that is assembled on a line where the QFN reflow profile is not qualified. The trade is thermal: the same 3 A in a larger plastic body with a smaller thermal pad relies on the copper around the pins, and the derating has to be checked against the enclosure rather than against the data sheet alone.
Key parameters from the SLVSG98B document
| Input range | 2.25 V to 5.5 V, UVLO between 2.05 V and 2.25 V rising |
| Output range | 0.5 V to 4.5 V adjustable through the FB divider |
| Output current | 3 A rated on this member |
| Feedback voltage | 500 mV typical with a 1 per cent total error over temperature |
| Switching frequency | 2.0 MHz quasi fixed, 100 per cent duty mode for a falling input |
| High side resistance | 35 milliohm typical and 57 milliohm maximum at 5 V input |
| Low side resistance | 18 milliohm typical and 29 milliohm maximum at 5 V input |
| Quiescent current | 7 nA typical and 17 nA maximum, device not switching |
| Shutdown current | 100 nA typical and 700 nA maximum with the enable low |
| Soft start | 180 to 440 microseconds standard, 530 to 1300 microseconds on the K options |
| Power good | Open drain window comparator, 96 and 92 per cent below, 110 and 105 per cent above |
| Package | DRL SOT583 of 1.6 mm by 2.1 mm, thermal shutdown at 150 degrees |
Where 3 A in a leaded body earns its place
Industrial boards that have to survive a conformal coat, a potting compound or a wide temperature excursion often prefer a leaded package because the solder joint can be inspected and reworked. The SOT583 gives that option at 3 A, which is the current class of a radio power amplifier rail, a small motor driver or a bank of LEDs. The part keeps the nanoamp quiescent current of the family, so it also suits a product that transmits at 3 A for a second and sleeps at 7 nA for an hour.
The vendor notes on the 4 A member that continuous operation at its full rating above 105 degrees junction reduces lifetime, which is a reminder that the current rating is a thermal statement, not an electrical limit. At 3 A in the SOT583 body the same caution applies earlier, because the plastic body and the smaller pad have a higher thermal resistance than the QFN. A 3 A rail that runs warm should be checked at the enclosure temperature, with the copper area that the board actually has.
The family also offers an output discharge switch and, on one option, a latch off response to a short circuit or an overvoltage event. On a board where the 3 A rail feeds a module that must come back only after a supervisor resets it, the latch off option is the correct one, and it has to be named on the order because the catalogue entry does not carry the option bit.
Where this part fits
Radio and PA rails on portable terminals, industrial sensor heads, LED drivers, small motor control boards and any product that needs 3 A with a leaded package and nanoamp standby. The substitution notes we keep for these families are at pin to pin cross reference and power management cross reference.
What to check before a purchase order
Check that the reel carries the DRL body. The same 3 A function exists in the RZE WQFN of 1 mm by 2 mm, and the two are not interchangeable on a board, because the footprints differ. The order code ends in DRL for the SOT583 and RZE for the QFN, and the packing label is the only place that distinction is printed when the parts arrive.
Check the input capacitor. A 2 MHz converter with a 3 A load draws its current in short pulses and the input capacitor carries most of the ripple, so a 4.7 microfarad part in a small case with a high ESR will show more input ripple than the data sheet curve. The receipt check we run on these reels and the marking check are described at incoming inspection plan.
Questions that come up on this part
Is the 3 A SOT583 part a drop in for the 2 A part, is a common question. Inside the DRL package the pinout is the same across members, so the part will run, but the current limit moves with the member and the inductor and the output capacitor have to be rechecked. A board that was signed off at 2 A with a 2.5 A inductor will see a saturated inductor at 3 A before the converter limits.
The other question is whether the 3 A rating holds at 5 V input and 3.3 V output. It does electrically, because the 100 per cent duty mode is available and the current limit sits above the rating, but at a duty cycle near 90 per cent the low side conducts only briefly and the loss moves into the high side and the inductor, so the thermal check is the one that decides.