Contact Us

TPS6282533DMQR

Brand: Texas Instruments
Texas Instruments TPS6282533DMQR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS6282533DMQR — Power Management & Signal Chain | Superb Automation

TPS6282533DMQR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS6282533DMQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS6282533DMQR fixed 3.3 V at 2 A with 4 microamp quiescent current

The TPS6282533DMQR is the 2 A, 3.3 V member of the TPS6282x family, a synchronous step down converter that takes 2.4 V to 5.5 V in and holds a quiescent current of 4 microamp, which is low enough that the converter can stay enabled in a standby state rather than being switched off. It is built on DCS-Control, runs at 2.2 MHz, holds 1 per cent output accuracy over the full junction range, and is available as an integrated inductor module, the TPSM82822, for boards that would rather not place the inductor.

The high side FET is 26 milliohm, the switch current limit for the 2 A members is 2.74 A minimum, 3.3 A typical and 3.9 A maximum, and the fixed 3.3 V output is trimmed to 3.267 V, 3.3 V and 3.333 V, which is 1 per cent across the window. Load regulation is 0.1 %/A, soft start is 1.25 ms to 95 per cent of the nominal output, and the power good output has a 94 to 98 per cent rising window and a 90 to 94 per cent falling window. Thermal shutdown is at 150 degrees junction, and the negative current limit on the A members is 1.6 A.

The 4 microamp figure is the whole point. A converter that draws 20 microamp when enabled cannot be left on in a product that has to survive a year on a coin cell, so the board ends up with a load switch and a second always-on regulator. At 4 microamp the main rail itself can be the standby rail, which removes a component and a failure mode from the board. The catch is that the figure applies to the no load, not switching condition, and the rest of the node has to be built to the same standard.

Key parameters from the SLVSEF9I document

Input range2.4 V to 5.5 V, covering a single cell and a 3.3 V or 5 V rail
Output3.3 V fixed on this member, 2 A rated, 1 per cent accuracy over the junction range
Switching frequency2.2 MHz in PWM, with power save operation at light load
Quiescent current4 microamp typical and 10 microamp maximum with the enable high and no load
High side resistance26 milliohm, which is what keeps the loss low at 2 A
Current limit2.74 A minimum, 3.3 A typical and 3.9 A maximum on the 2 A members
Negative current limit1.6 A on the A members of the family
Soft start1.25 ms to 95 per cent of the nominal output
Power good94 to 98 per cent rising and 90 to 94 per cent falling, 0.4 V low level
Load regulation0.1 %/A in PWM mode
Thermal shutdown150 degrees junction with hysteresis
Package6 pin SOT-563, 1.6 mm by 1.6 mm, DMQ body

A standby rail that is also the working rail

Most products end up with two power paths: a working converter that is efficient at load and an always-on regulator that is efficient at microamps. The two meet at a load switch, and the switch is where the failure modes live. A converter with a 4 microamp quiescent current removes that split, because the same device can deliver 2 A and then idle at microamps with the load disconnected or drawing almost nothing.

The condition matters. The 4 microamp figure is specified with the enable high, no load, and the device not switching. A rail with a 100 kilohm divider on it draws 33 microamp at 3.3 V and the converter will be switching to supply it, so the number that shows up on the bench is the switching loss plus the divider. The standby budget has to be computed across the node, and a fixed voltage member like this one removes the divider that would otherwise dominate it.

The other half is the power good window. A 94 to 98 per cent rising threshold means PG asserts only when the rail is genuinely in tolerance, which is what a processor needs before it releases reset. A part that asserts PG at 80 per cent of nominal lets a processor start on a rail that is still climbing, and the resulting brownout is blamed on the processor.

Where this part fits

Battery powered instruments, wearables, wireless sensors, industrial nodes that have to idle for years and any board where a 3.3 V rail at 2 A has to be its own standby supply. Our desk keeps the cross reference for the family across the 1 A to 4 A members, see power management cross reference and pin to pin cross reference.

What to check before a purchase order

Check the part number against the current and voltage table. The family spans 1 A, 2 A, 3 A and 4 A with fixed and adjustable outputs, all in the same two packages, and the digits in the middle of the code carry both. A reel picked by family name will eventually deliver a 1 A part to a 2 A rail, and the board will work until the load steps.

Check the standby budget across the whole node, including the feedback divider if an adjustable member is used, the leakage of the load switch and the quiescent current of whatever monitors the rail. Check the inductor against the 3.9 A top of the current limit as well, since a 2 A inductor will saturate during a fault. See incoming inspection plan for the goods inwards check on this body.

Questions that come up on this part

Does the 4 microamp figure include the feedback divider, is the first question. On this fixed voltage member there is no external divider, so the figure is the device alone. On the adjustable members of the same family the divider adds its own current, and at 3.3 V a 1 megohm pair adds 3.3 microamp, which nearly doubles the total.

The second question is whether the 2.2 MHz rate limits the input voltage. It does not, but the minimum on time does: at 5.5 V in and 3.3 V out the duty cycle is 60 per cent, which is comfortable, and the difficult case is a high input with a low output on the adjustable members. A fixed 3.3 V output from a 5 V rail is well inside what the loop can hold.