Contact Us

TPS62801YKAR

Brand: Texas Instruments
Texas Instruments TPS62801YKAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62801YKAR — Power Management & Signal Chain | Superb Automation

TPS62801YKAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62801YKAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62801YKAR: 1 A step-down converter in a 0.35 mm pitch wafer level package with 2.3 uA quiescent current

TPS62801YKAR is a step-down converter small enough to sit next to the load it feeds and efficient enough to stay on in a battery product in a DSBGA (YKA) body of 6 pins. It takes 1.75 V to 5.5 V in, delivers 1 A, switches up to 4 MHz, holds 1 per cent output accuracy and draws 2.3 uA of quiescent current, in a 1.05 mm by 0.70 mm six ball package with a 0.35 mm ball pitch.

Order code and package

Ordering stringTPS62801YKAR, the 1 A member in the YKA wafer level body on a large reel
Body6 ball DSBGA, 1.05 mm by 0.70 mm, 0.35 mm pitch
Family membersTPS62800 and TPS62801 at 1 A, TPS62802, TPS62806, TPS62807 and TPS62808 at 0.6 A, all in the same body and pinout
Output settingSixteen selectable voltages plus one fixed option through the R2D pin, with no external divider needed
Mode pinThe same pin that selects the output also selects power save or forced PWM after start up
Input range1.75 V to 5.5 V, which covers a single lithium cell and a 3.3 V or 5 V rail
Switching frequencyUp to 4 MHz, with the switching rate following the load so that efficiency holds at light currents

Electrical parameters that decide the application

Output current1 A on this member, with the high side switch current limit at 1.3 A minimum, 1.45 A typical and 1.55 A maximum
Low side limit1.2 A minimum, 1.35 A typical, 1.45 A maximum
Switch resistance120 milliohm typical and 170 milliohm maximum on the high side at 500 mA, 80 milliohm typical and 115 milliohm maximum on the low side
Quiescent current2.3 uA typical and 4 uA maximum in power save with the output at 1.2 V and no load, 2.5 uA when switching
Shutdown current120 nA typical, 250 nA maximum, which is the figure that decides shelf life in a coin cell product
Accuracy1 per cent over the rated range, which is tight enough for a processor core rail without a feedback divider
Undervoltage lockout1.75 V rising and 1.7 V falling, with 1.65 V and 1.56 V as the limits
Enable thresholds0.8 V minimum for a high, 0.4 V maximum for a low, 25 nA of input bias current, and a 500 k pull down so the pin does not float
R2D output selectionThe resistor from the R2D pin to ground is converted once at start up into one of sixteen output settings, so the resistor tolerance sets the output and no divider current flows afterwards
Leakage10 nA typical into the switch node when the part is off, so a disabled rail does not load its neighbour

Family variants and how they differ

TPS62800 against TPS62801Both are 1 A members with the same current limits, separated by the fixed output option and the default mode at start up
The 0.6 A membersTPS62802 and the TPS62806 to TPS62808 group carry a lower switch current limit, 0.95 to 1.2 A, and are the right choice when 600 mA is enough and a smaller inductor is wanted
R2D against a dividerThe resistor to ground is measured once and latched. That removes the divider current from the quiescent budget, which is the whole point of a 2.3 uA part, and it removes a node that could pick up noise
Power save against forced PWMPower save drops the switching frequency at light load and holds efficiency; forced PWM keeps a constant ripple and a predictable spectrum at the cost of a few microamps
Package realityA 0.35 mm pitch body needs a 0.4 mm or finer trace and space rule on the outer layer, and the board house has to be able to place it. It is not a part for a two layer prototype board with 0.2 mm rules
What it is notThere is no external synchronisation, no soft start adjustment and no power good output. The part is meant to be small, and every pin it does not have is a millimetre saved

Points to check before this part goes on a BOM

The 1 per cent accuracy comes from the internal feedback with R2D selection. A board that copies a divider from an adjustable part and expects the same accuracy will be disappointed.

The R2D resistor is converted once, at start up. An undervoltage event during that conversion can latch the wrong output, which the vendor states in the functional description, so a rail that browns out repeatedly should be checked for the correct setting after recovery.

Quiescent current of 2.3 uA applies in power save with the device not switching. In forced PWM the figure is two orders of magnitude higher, and the mode pin is what decides which one a product gets.

The 1 A rating is bounded by the 1.3 A minimum high side limit. A load that pulls 1.2 A at start up is inside the limit but outside the rating, and the output will sag rather than regulate.

A 0.35 mm pitch wafer level package has no compliant leads. Board flex and thermal cycling go straight into the balls, so the land pattern and the underfill decision come from the package drawing, not from habit.

The 4 MHz switching rate is what allows a 0.47 uH inductor. Efficiency at 4 MHz is lower than at 2 MHz, and the trade is board area against a couple of points of efficiency.

Why the quiescent current is the specification that matters

In a product that sleeps for 99 per cent of its life, the converter runs in power save with a few microamps of load. A regulator that draws 30 uA of its own quiescent current doubles or triples the sleep budget, and the battery life figure on the datasheet of the product is written by the converter, not by the processor.

The 2.3 uA figure here is achieved partly by the R2D output selection: a conventional divider would draw a few microamps continuously and would dominate the budget. That is why the resistor is measured once and latched rather than left in circuit.

Where this order code fits

Smartphones, wearables, hearables, sensor nodes and any board where a rail has to be generated inside a few millimetres of the load. The 0.35 mm pitch body is meant for a dense printed circuit with a 0.4 mm class via and trace geometry, and the 4 MHz switching keeps the inductor at 0.47 uH so the whole converter fits under a shield can. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can it run from a single lithium cell down to 3.0 V? Yes. The input range starts at 1.75 V, and the lockout sits at 1.75 V rising and 1.7 V falling, so a cell at 3.0 V is well inside the range.

How is the output voltage set? By a resistor from the R2D pin to ground, selected from sixteen settings plus one fixed option. The value is converted at start up and held.

Does it need an external compensation network? No. The loop is internal and the data sheet gives the inductor and capacitor values for each output setting.

What is the smallest inductor it will work with? The 4 MHz switching rate allows a 0.47 uH part. Going smaller raises the ripple current and the peak switch current, which eats into the 1.3 A limit.

Is there a power good signal? No. The six ball body has enable, mode and output selection only. A board that needs a power good has to derive it elsewhere.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.