TPS62751DSKR
Product Specifications
TPS62751DSKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62751DSKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62751DSKR adjustable step down with a programmable input current limit
The TPS62751DSKR is the adjustable member of the TPS62750 and TPS62751 pair, a synchronous step down converter built for USB powered equipment: it takes 2.9 V to 6 V in, delivers up to 1300 mA of average input current, and carries a programmable average input current limit that a board can set to match the host port it is plugged into. That last feature is the reason the part exists. A USB host will drop the port if the peripheral draws more than the negotiated current, and a converter that limits its own input current is how a peripheral stays inside the envelope.
The current limit has two ranges: 50 mA to 300 mA for a low current setting, and 300 mA to 1.3 A for the high range, both with 10 per cent accuracy and both set by an external resistor. The switching rate is 2.25 MHz typical, quiescent current is 30 microamp, shutdown current is 0.2 microamp typical and 3 microamp maximum, and the undervoltage lockout sits at 2.4 V falling and 2.9 V rising. Efficiency is quoted above 90 per cent at nominal conditions, and the power save mode takes over below the discontinuous conduction boundary.
The part is specified over minus 40 to 85 degrees ambient, sits in a 10 pin SON body of 2.5 mm by 2.5 mm, and is available in tape and reel at 3000 pieces with the R suffix. Output is adjustable on this member, fixed on the sibling, and the reference is scaled so that a divider from the feedback pin sets any voltage in the range the input allows. A 3.6 V output from a 5 V host is the typical application the document shows.
Key parameters from the SLVS955A document
| Input range | 2.9 V to 6 V, with the lockout at 2.4 V falling and 2.9 V rising |
| Output | Adjustable on this member, up to 1300 mA of average input current |
| Input current limit | 50 mA to 300 mA in the low range, 300 mA to 1.3 A in the high range, 10 per cent accuracy |
| Switching frequency | 2.25 MHz typical, with power save mode below the discontinuous boundary |
| Quiescent current | 30 microamp with no load and the device not switching |
| Shutdown current | 0.2 microamp typical and 3 microamp maximum with the enable pin at ground |
| Efficiency | Above 90 per cent at the nominal operating conditions |
| Power save boundary | Entered when the inductor current in the low side switch reaches zero |
| Ambient range | Minus 40 to 85 degrees |
| Package | 10 pin SON, 2.5 mm by 2.5 mm, DSK body, 3000 pieces on a reel with the R suffix |
| Family | Fixed output version in the TPS62750, adjustable in this TPS62751 |
Why a converter needs its own input current limit
A USB port is a current source with a trip. The host measures the load, and if the peripheral exceeds what it negotiated, the port either limits the voltage or shuts down. A DC to DC converter that draws whatever it needs to hold its output will trip that protection the moment the load steps, and the peripheral resets. The fix is a converter whose input current is bounded below the port limit, which is what the programmable average input current loop does here.
The loop acts on the average rather than the peak, which is what matters for a host that measures over milliseconds. A peak current limit alone would still allow a burst that trips the port. The 10 per cent accuracy means the set point has to be chosen with margin: a 500 mA port should be asked for 400 mA, not 495 mA, because the tolerance and the ripple both add on top.
When the limit is reached the output voltage falls rather than the input current rising. That is the correct behaviour for a peripheral, because it degrades gracefully instead of resetting the host port, and the downstream circuit sees a sag rather than a disconnection. A board that needs the output to hold at all costs should not use a limited converter, and a board that is plugged into an unknown host should.
Where this part fits
USB peripherals, wireless modems that draw from a host port, portable instruments that charge and run from the same connector, and any board that has to stay inside a port current envelope while delivering a regulated rail. Our desk keeps the cross reference for the USB class and the drop in notes, see power management cross reference and how to verify a drop in replacement.
What to check before a purchase order
Check which member the board needs: the fixed and adjustable versions share the document and the body, and a substitution leaves the divider driving a feedback pin that expects a fixed setting. Check the current limit resistor against the port the product will meet, and check the 2.9 V rising lockout against a host that ramps its 5 V slowly, since a slow ramp can leave the part in a start stop cycle.
Check the inductor against the high range limit as well as against the load, because the current loop acts on the average and a saturated inductor makes the average meaningless. See incoming inspection plan for the receipt check on a 10 pin SON.
Questions that come up on this part
Can the input current limit be changed at run time, is a question that comes up on multi host products. It is set by a resistor, so it is fixed at assembly; a board that has to meet both a 500 mA and a 900 mA host needs either two resistors with a switch or a different part. The two ranges are selected by the resistor value, so the low and high range are not a mode pin away from each other.
The second question is whether the 1300 mA figure is the output current. It is the average input current, so the output current depends on the conversion ratio: at 5 V in and 3.6 V out, 1.3 A in is about 1.6 A out at 90 per cent efficiency, and at 5 V in and 1.2 V out it is well below that. Reading the number as an output rating is the mistake this part invites.