TPS62480RNCR
Product Specifications
TPS62480RNCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62480RNCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62480RNCR 6 A from two 3 A phases at 2.2 MHz
The TPS62480RNCR is a two phase synchronous step down converter that takes 2.4 V to 5.5 V in and delivers 6 A continuous from two phases of 3 A each, with an output adjustable from 0.6 V to 5.5 V. Running two phases 180 degrees apart halves the input ripple and doubles the effective ripple frequency, so the input capacitor bank and the output filter are both smaller than a single phase converter of the same current would need. The reference is 0.6 V with 1 per cent accuracy in PWM, and the switching rate is typically 2.2 MHz.
High side on resistance is 36 milliohm typical and 98 milliohm maximum on phase one, and 29 milliohm typical with 72 milliohm maximum on phase two, which is the kind of number that makes 6 A in a low profile package possible. Quiescent current is 23 microamp typical and 38 microamp maximum, shutdown current is 0.5 microamp typical and 18.5 microamp maximum, and thermal shutdown is at 160 degrees junction. Load regulation is quoted as 0.02 %/A and line regulation as a small fraction of a per cent per volt, both in PWM mode.
The feedback node is not a plain divider input. The device has an RS pin that injects a current into the feedback node, which allows the output to be trimmed or margined without changing the resistors, and a VSEL pin that selects between a resistor set voltage and a preset level. Together they let a board set a nominal rail and move it during test, which is useful on a point of load supply that has to be margined to plus or minus 5 per cent before it ships.
Key parameters from the SLVSCL9A document
| Input range | 2.4 V to 5.5 V, covering 3.3 V and 5 V supplies and a backup rail that sags |
| Output current | 6 A continuous from two phases of 3 A each |
| Output voltage | 0.6 V to 5.5 V, set by a divider with the RS and VSEL pins for trim and selection |
| Switching frequency | 2.2 MHz typical, with the two phases 180 degrees apart |
| High side resistance | 36 milliohm typical on phase one, 29 milliohm typical on phase two, at 3 V input |
| Reference | 0.6 V with 1 per cent accuracy in PWM and 65 nA of leakage at the feedback pin |
| Quiescent current | 23 microamp typical and 38 microamp maximum with the device not switching |
| Shutdown current | 0.5 microamp typical and 18.5 microamp maximum with the enable pin low |
| Soft start | Internal, with the SS/TR pin available for tracking and for a longer ramp |
| Thermal shutdown | 160 degrees junction in PWM mode with hysteresis |
| Package | Low profile QFN with the two switch nodes brought out separately |
What the second phase actually buys
A single phase 6 A converter at 2.2 MHz would need an inductor of about 0.5 microhenry with a saturation current above 8 A, and an input capacitor bank able to absorb a 6 A square wave. Two phases at 3 A each use two smaller inductors and split the input current into two pulses 180 degrees apart, which largely cancel in the input capacitor. The result is a lower profile and a quieter input, at the cost of one extra inductor and one extra switch node to keep short.
The output ripple also improves, because the two phases deliver current at twice the rate and the ripple interleaves. For a 2.2 MHz part that means an effective 4.4 MHz output ripple, so the output capacitor can be a small ceramic rather than a tantalum or a polymer part. On a point of load rail that has to fit under a processor, that is the whole argument.
The two switch nodes are the price. Each one is a square wave carrying 3 A, and both have to be kept away from the feedback trace, the RS injection node and any analog signal. A board that routes them together to save space will couple them into each other and into the sense line, and the resulting jitter shows up as output noise at a frequency nobody expects.
Where this part fits
Processor and FPGA point of load rails, DDR memory supplies, low profile modules and any board that needs 6 A from a 5 V or 3.3 V input in a package that fits under a heat spreader. Our desk keeps the cross reference for the multiphase class and the second source notes, see power management cross reference and how to verify a drop in replacement.
What to check before a purchase order
Check the inductor pair against the current limit of each phase rather than against the 3 A nominal, and check that the two inductors are the same part number. A mismatch of 20 per cent between the phases shifts the current share, and one phase will run hotter than the other at full load without any fault being reported.
Check the RS pin. If the board does not use the trim function, the pin still needs its specified termination, and a floating node on a current injection input will move the output voltage with temperature and with board cleanliness. See incoming inspection plan for the receipt check on this package.
Questions that come up on this part
Is 6 A available at 2.4 V input, is a question that comes from battery backed products. It is, but at 0.6 V output the duty cycle is 25 per cent and the losses are dominated by the low side, and at 5.5 V output the part is in dropout and the output follows the input. The usable window for full current is narrower than the input range suggests.
The second question is whether the part can be used as a single phase 3 A converter by leaving one phase unconnected. It cannot: the two phases share one control loop, and disabling one leaves the loop compensating for a power stage that is not there. The family has smaller members for that case.