TPS62420QDRCRQ1
Product Specifications
TPS62420QDRCRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62420QDRCRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62420QDRCRQ1: 2.25 MHz dual step down, 600 mA and 1000 mA, automotive qualified, in a 10 pin VSON
TPS62420QDRCRQ1 is a dual synchronous step down converter that makes two rails from one input with a fixed 2.25 MHz clock and 180 degrees of phase shift between the channels in a VSON body of 10 pins. It runs from 2.5 V to 6 V, delivers 600 mA on one channel and 1000 mA on the other, and holds plus or minus 1 per cent output accuracy in PWM mode. Both converters together draw 32 uA typical in power save mode against 1.2 uA in shutdown, and the 3 mm by 3 mm VSON body is qualified to AEC-Q100 grade 1.
Order code and package
| TPS62420QDRCRQ1 | 10 pin VSON (DRC), 3.00 mm by 3.00 mm, 3000 pieces on a large reel, marking OEP, moisture level 3 with a 168 hour floor life |
| Second addendum row | the same string appears again with a nickel palladium gold finish and the same 3000 piece reel, so the finish has to be named on the order |
| Output 1 | 600 mA, adjustable from 0.6 V to the input voltage |
| Output 2 | 1000 mA, adjustable from 0.6 V to the input voltage |
| Temperature grade | AEC-Q100 grade 1, minus 40 C to plus 125 C junction |
Electrical parameters that decide the application
| Input voltage | 2.5 V to 6 V, which covers a single lithium cell and a 5 V bus |
| Output voltage | 0.6 V to the input voltage on both channels, from a 600 mV reference |
| Output current | 600 mA on channel one, 1000 mA on channel two |
| Switching frequency | 2.25 MHz fixed, with the two channels 180 degrees apart |
| Output accuracy | plus or minus 1 per cent in PWM mode, with the PFM accuracy window wider |
| Quiescent current | 19 uA with one converter in power save mode, 32 uA with both |
| Shutdown current | 1.2 uA typical and 3 uA maximum with both enable pins low |
| Duty cycle | 100 per cent for the lowest dropout, so the output can follow a falling input |
| Interface | EasyScale one pin serial interface for changing the output voltage during operation |
| Soft start | internal ramp, no external capacitor needed |
What the two channels can do together
| Phase shift | 180 degrees between the channels, which halves the input ripple current and lets one input capacitor serve both |
| Independent enables | EN1 and EN2 are separate, so one rail can be off while the other runs |
| Power save mode | entered automatically at light load, exited on a load step, with the MODE pin able to force PWM instead |
| EasyScale | one wire, used for dynamic voltage scaling on a processor rail that changes frequency at run time |
| Def pin | sets the default output voltage, so the rails come up at a known level before any serial command |
| 100 per cent duty | the high side FET stays on when the input falls to the output, which is how a 3.3 V rail survives a 3.4 V battery |
Points to check before this part goes on a BOM
The two channels are not equal, and the 600 mA and 1000 mA ratings belong to specific channels on specific pins. A board that puts the heavier load on channel one runs into the current limit earlier than the circuit suggests. The vendor reference circuit puts the processor core on channel two and the input output rail on channel one, which is the arrangement the thermal numbers were measured with.
The 180 degree phase shift is worth more than it looks on a dual converter. With both channels switching at the same instant the input capacitor sees the sum of two ripple currents; with the channels opposed it sees the difference, and the RMS rating of the input capacitor falls accordingly. On a 3 mm by 3 mm board where the capacitor is a 0603 or an 0805, that difference is the whole margin.
The plus or minus 1 per cent accuracy figure is a PWM mode number. In power save mode the output is allowed to rise slightly above nominal and the accuracy window widens to about 2.5 per cent, which is how the converter keeps efficiency at light load. A rail feeding an ADC that is read while the load is idle sees the wider window, not the 1 per cent one.
The quiescent current of 32 uA for both converters is measured with the outputs unloaded and the part in power save mode. That is the figure for a product that stays enabled with no load, which is the sleep state of most battery equipment. A product that forces PWM to keep the spectrum clean draws considerably more and should not quote the 32 uA figure in its own budget.
The EasyScale interface is a single wire and it changes the output voltage while the converter runs. It is useful for a processor that drops its core voltage at low frequency, and it is also a way to lose a rail if the serial timing is wrong. The default voltage set by the Def pin is what the rail comes up at before any command, so the divider and the Def pin have to agree or the first power up is at the wrong level.
The 100 per cent duty cycle mode is the feature that keeps a 3.3 V rail alive on a battery that has fallen to 3.4 V. Below that the converter cannot hold the rail and the output follows the input minus the drop across the high side FET. On a lithium cell that is the last 20 per cent of the discharge curve, and a product that resets there has a converter problem rather than a battery problem.
The moisture level 3 with a 168 hour floor life is the practical difference between this part and a consumer grade equivalent. An opened reel has to be used or baked inside a week, and a production line that holds reels between builds needs dry storage. The automotive qualification also fixes the temperature grade and the test flow, which is why the order code is longer and the price is higher.
Where this order code fits
It supplies the processor core and the input output rail in automotive infotainment and cluster modules, dashboard cameras and body electronics, where two rails have to come from a 5 V or battery bus on a board with very little space. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the CAN Bus Transceiver Selection page.
Questions buyers ask
Can both channels deliver their rated current at the same time? Yes, 600 mA and 1000 mA simultaneously, within the thermal limits of the 3 mm by 3 mm body. The dissipation at 5 V in and 1.2 V out is what limits the combination, not the current ratings.
What is the accuracy in power save mode? Wider than the 1 per cent PWM figure, around 2.5 per cent, because the output is allowed to sit above nominal at light load. Use the PWM figure only when the MODE pin forces fixed frequency.
Does it need external compensation? No, the loop is internally compensated and the output capacitor range in the vendor table is what keeps it stable.
What does the EasyScale pin do? It changes the output voltage over a single wire while the converter runs, for dynamic voltage scaling. The voltage it comes up at before any command is set by the Def pin.
Is the part qualified for automotive use? Yes, AEC-Q100 grade 1, minus 40 C to plus 125 C junction. The Q1 suffix and the DRC body are part of that qualification.
What happens when the battery falls below the set output? The converter runs at 100 per cent duty and the output follows the input minus the high side drop. Below that the rail is no longer regulated.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Vendor Consolidation page sets out the checks that keep a substitute from failing on the bench.