TPS62262DDCR
Product Specifications
TPS62262DDCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62262DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62262DDCR: 2.25 MHz 600 mA Step-Down Converter
TPS62262DDCR is a 2.25 MHz synchronous step-down converter for small loads in a SOT-23 body of 6 pins. It switches at 2.25 MHz from 2.3 V to 6 V in and delivers 600 mA, which allows a 2.2 uH inductor and a 10 uF output capacitor, so the whole converter fits in the area of the connector it feeds.
Order code and package
| Ordering string | TPS62262DDCR, SOT-23 (DDC), 2.90 mm by 1.60 mm |
| Family | TPS62260 to TPS62263, fixed and adjustable output versions |
| Package option | WSON-6 (DDC), 2.00 mm by 2.00 mm, for the same silicon |
| Input | 2.3 V to 6 V |
| Output | 600 mA from 2.5 V input, adjustable on this member |
| Mode | power save with automatic transition, or forced PWM |
Electrical parameters that decide the application
| Output current at 2.5 V to 6 V | 600 mA |
| Output current at 2.3 V to 2.5 V | 300 mA |
| Output current at 2.0 V to 2.3 V | 150 mA |
| Quiescent current, PFM | 15 uA, not switching |
| Shutdown current | 0.1 uA typ, 1 uA max |
| High side resistance | 240 mOhm typ, 480 mOhm max |
| Low side resistance | 185 mOhm typ, 380 mOhm max |
| Lockout | 1.95 V rising, 1.85 V falling |
| Logic thresholds | 1 V high, 0.4 V low, over the full input range |
| Thermal resistance | 67.8 C/W on one board, 226.9 C/W on the other |
Points to check before this part goes on a BOM
The 600 mA rating is conditional on the input, and the conditions are three: 600 mA from 2.5 V up, 300 mA between 2.3 V and 2.5 V, 150 mA between 2.0 V and 2.3 V. A two cell alkaline pack at end of life sits at 2.2 V and gets a quarter of the headline current, which is the number a battery product has to plan around.
The two switch resistances add to 425 mOhm at their typical values, which at 600 mA is 0.153 W of conduction loss, and the part switches 2.25 million times a second, so at 6 V in the switching loss overtakes conduction well before full load. That is why the efficiency curves peak at a few hundred milliamps and fall at the top of the range, not because the FETs are small.
Quiescent current of 15 uA in power save is 131 mAh over a year, and shutdown at 1 uA maximum is 8.8 mAh, so a product that sleeps for a year and leaves the converter enabled loses fifteen times what it would lose with the enable pulled low. The enable pin, not the load, is the standby decision.
The lockout releases at 1.95 V, but the recommended input starts at 2.3 V and the current table starts at 2.0 V. Between 1.95 V and 2.0 V the converter runs outside every published condition, which is a state a slowly rising battery rail will pass through on every cold start.
The two thermal numbers, 67.8 C/W and 226.9 C/W, differ by a factor of three for the same package and the same current, which is the copper under the part. In the SOT-23 the ground pin and the drain pad are the only heat path, so a 0.3 W loss is a 20 C or a 68 C rise depending on which board it is on.
Switching at 2.25 MHz is what allows a 2.2 uH inductor: at 3.6 V in and 1.2 V out the ripple is 161 mA, 27 percent of a 600 mA load, so the converter is in continuous conduction at full load and enters discontinuous below about 80 mA. The loop has to be stable in both regions, which is why the mode pin and the output capacitor are not free choices.
Forced PWM keeps the ripple at a fixed frequency, which a radio or an ADC prefers, and costs the 15 uA quiescent plus the switching loss at every load. Power save drops the quiescent into the microamp range and moves the ripple to a frequency a sensor can pick up, so the mode pin is an EMC decision as much as an efficiency one.
Where this order code fits
Handheld instruments, wireless sensors and portable audio use this part where a few hundred milliamps has to come from a battery or a 5 V bus with almost no board area. A wireless sensor that sleeps for a second and transmits for a millisecond is the load this part was sized for, and the 2.25 MHz switching keeps the inductor and the output capacitor small enough to sit under the radio can. The enable pin is the standby control and the mode pin is the noise control, so a battery product ends up driving both from a controller rather than strapping either. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.
Questions buyers ask
Is this the fixed or the adjustable version? Adjustable. The family mixes fixed and adjustable members, so the ordering suffix decides, and the adjustable part needs a divider on the feedback pin.
Why does the current rating change with input voltage? Because the current limit and the duty cycle interact at low input: 600 mA is only guaranteed from 2.5 V up, and the same part gives 150 mA at 2.0 V.
What inductor value is intended? 2.2 uH is the value the electrical table is written against, with 4.7 uF in and 10 uF out, so a different inductor changes the ripple and the loop.
Can the mode pin be left floating? No. It is a logic input with a defined threshold, and leaving it open puts the converter in an undefined mode; tie it high or low.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.