Contact Us

TPS62235DRYR

Brand: Texas Instruments
Texas Instruments TPS62235DRYR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62235DRYR — Power Management & Signal Chain | Superb Automation

TPS62235DRYR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62235DRYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62235DRYR: 2 MHz step-down converter, 1.2 V fixed output, 500 mA peak, 1 mm by 1.5 mm SON

TPS62235DRYR is a fixed 1.2 V synchronous step-down converter with a 2 MHz switching frequency and a 500 mA peak output current in a 1 mm by 1.5 mm body in a SON body of 6 pins. The whole converter including the inductor and the capacitors fits in about 12 square millimetres, which is the point of the family: it replaces a linear regulator on a core rail and cuts the loss without needing board area the product does not have. The 1.2 V output is fixed inside the package, so there is no divider.

Order code and package

TPS62235DRYRActive, SON-6 at 1.45 mm by 1.0 mm, 5000 pieces on a large reel, marking OQ
TPS62235DRYTActive, 250 pieces on a small reel, the same body, marking OR
TPS62232the 1.2 V member at 3 MHz, for boards that can accept the higher switching loss
Family rangefixed outputs from 1.0 V to 3.3 V across nineteen ordering strings in the same body
Junction rangeminus 40 to 125 degrees, which is a junction rating on a very small body

Electrical parameters that decide the application

Input voltage2.05 V to 6 V
Output1.2 V fixed on this string
Output currentup to 500 mA peak
Switching frequency2 MHz on this member, 3 MHz on others in the family
Quiescent current22 microamp typical in power save
Efficiencyup to 94 per cent
Rejectionup to 90 dB, which is why the part can replace a linear regulator
Shutdown currentless than 1 microamp

Family variants and how they differ

TPS622351.2 V at 2 MHz, the string on this page
TPS622321.2 V at 3 MHz, smaller inductor, higher switching loss
TPS622311.8 V at 3 MHz, the common core rail option
MODE pinpulling it high forces PWM across the load range for a clean spectrum
Body1.45 mm by 1.0 mm by 0.6 mm, six pins, no thermal pad

Points to check before this part goes on a BOM

Five hundred milliamp is a peak rating. The continuous current depends on the input voltage and the thermal path, and in a body this small the board copper does most of the work. A 1.2 V core rail at 400 mA from a 3.7 V cell dissipates a few hundred milliwatt in the converter and the inductor, which is close to what a 1 mm body can pass to a small copper island.

The reel size is five thousand, not three thousand. That is printed in the addendum for the DRY body and it changes how a repair quantity is handled: a 500 piece order is a broken reel, and the split has to be agreed before the order. The small reel member is a separate ordering string with a separate marking.

Twenty two microamp in power save is high for a wearable. The part is efficient at load and unremarkable at no load. A product that keeps the rail on while it sleeps will spend more on the converter than on the load. The better arrangement is to switch the rail off and let a nanoamp class regulator keep the always on domain alive.

Ninety decibel rejection is the reason to use it instead of a linear regulator. A 1.2 V core rail that has to be quiet can be fed from a switching converter with high rejection at the frequencies that matter, which removes the linear regulator and its dropout loss. The rejection falls with frequency, so the switching frequency of the upstream converter has to be checked against the curve.

The MODE pin forces PWM and removes the light load saving. That is the right trade for a radio or an analogue rail that cannot tolerate the skip ripple, and the wrong trade for a product that spends most of its life at a few milliamp. The pin has no internal pulldown on this member, so it has to be tied to a defined level rather than left floating.

A floating enable can turn the part on. The family table shows this member without an internal pulldown on the enable and mode pins. On a board where the enable comes from a microcontroller that is unpowered during test, the converter can come on unexpectedly. A 100 k pulldown fixes it and costs almost nothing.

Two megahertz against three megahertz is a real difference. The 3 MHz members allow a smaller inductor and a smaller output capacitor, at the cost of switching loss. At 1.2 V out and 3.7 V in the duty cycle is short and the switching loss dominates, so the 2 MHz member is the more efficient of the two at the same load.

The output is fixed and that is the point. There is no divider, no feedback pin brought out and no divider drift. On a core rail that needs 1.2 V, that removes two parts and the error they contribute. It also means the family cannot be used for a rail that is not one of the nineteen published voltages.

A 0.6 mm maximum height sets the assembly constraint. The part is built for a module or a wearable where the total height matters. That rules out a shielded inductor of any size, so the inductor choice is limited to what fits the height budget, and the ripple current follows from that choice rather than from the converter.

What to confirm before this part goes on a purchase order

Confirm the fixed voltage and the switching frequency. Nineteen strings share one body, and a 1.8 V member in a 1.2 V socket is not detectable from the reel label unless the marking is checked.

Ask for the date code and the packing quantity, and note that this body ships on a 5000 piece reel. A prototype order will be a broken reel, so the split and the seal date have to be agreed with the supplier.

For a core rail, state the load current and the allowed height in the same message. The body height limits the inductor and the inductor sets the ripple, so the two numbers cannot be chosen separately. A module with a height limit needs the inductor selected first and the converter second, not the other way round.

Where this order code fits

It makes a 1.2 V core rail at up to 500 mA peak inside a 1 mm by 1.5 mm footprint, next to an MCU in a wearable or a portable audio product. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Reduce Component Cost page.

Questions buyers ask

Is 500 mA a continuous rating? It is a peak rating. The continuous current depends on the input voltage, the inductor and the copper area under the part, and in a body this small the thermal path sets the limit long before the silicon does.

Can it replace a linear regulator directly? Yes for a 1.2 V rail, which is why the family exists. The rejection is high enough at the frequencies that matter, and the efficiency removes the dropout loss. The inductor and the capacitors need board area that the linear regulator did not.

What happens if the enable pin floats? This member has no internal pulldown, so the pin can sit at an undefined level and the converter can come on. A 100 k resistor to ground defines the off state and should be on every board that does not drive the pin from an active source.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.