TPS622311DRYR
Product Specifications
TPS622311DRYR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS622311DRYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS622311DRYR 1.1 V at 2 MHz from a single lithium cell
The TPS622311DRYR is the 1.1 V member of the TPS6223xx family, a synchronous step down converter in a 6 pin USON body of 1.45 mm by 1.00 mm and 0.6 mm high. It runs at 2 MHz, takes 2.05 V to 6 V in, delivers up to 500 mA of peak output current, and holds the switching frequency in a narrow band through a hysteretic PWM loop rather than a fixed clock with an error amplifier. The 2.05 V input floor is what makes it a single cell part: a lithium cell at end of discharge still sits above it, and two alkaline cells in series do too.
The reference is 0.7 V with a 2 per cent window, the output accuracy is quoted at 2 per cent, and the high side on resistance is 600 milliohm typical and 850 milliohm maximum at 3.6 V input. The switch current limit is 690 mA minimum, 850 mA typical and 1050 mA maximum, which is what supports a 500 mA peak load: the limit sits comfortably above the load and above the saturation point of the 1 microhenry inductor the 2 MHz rate allows. Quiescent current is 25 microamp, shutdown current is 0.1 microamp typical, and thermal shutdown is at 150 degrees junction.
1.1 V is a core rail, not a system rail. It belongs behind a processor or an FPGA that has already been characterised at that voltage, and the tolerance that matters is the one at the load rather than at the converter output. The hysteretic loop responds to the output falling below a threshold rather than to a clock edge, so the transient response is fast without an external compensation network, and the ripple stays small across the load range because the loop corrects on every cycle.
Key parameters from the SLVS941G document
| Input range | 2.05 V to 6 V, so a single lithium cell or two alkaline cells in series |
| Output | 1.1 V fixed on this member, up to 500 mA of peak output current |
| Switching frequency | 2 MHz nominal on this member, 3 MHz on most of the family |
| Reference and accuracy | 0.7 V internal reference, 2 per cent output accuracy over the load range |
| High side resistance | 600 milliohm typical and 850 milliohm maximum at 3.6 V input |
| Current limit | 690 mA minimum, 850 mA typical and 1050 mA maximum |
| Quiescent current | 25 microamp with the enable high and the device not switching |
| Shutdown current | 0.1 microamp typical and 1 microamp maximum |
| Minimum on time | 135 ns with the mode pin high, which limits the usable duty cycle at high input |
| Thermal shutdown | 150 degrees junction with hysteresis |
| Junction range | Minus 40 to 125 degrees |
| Package | 6 pin USON, 1.45 mm by 1.00 mm, DRY body, marking QF |
What 2 MHz and a hysteretic loop do for a core rail
A core rail sees load steps that are faster than any converter can follow: a processor wakes, the current goes from 5 mA to 400 mA in a few hundred nanoseconds, and the output moves until the loop reacts. A hysteretic loop reacts within one switching period, which at 2 MHz is 500 ns, so the excursion is short. A fixed frequency voltage mode loop with a 20 kHz crossover takes tens of microseconds and needs a large output bank to hold the rail in the meantime.
The price is a switching frequency that is not perfectly constant. The loop turns the high side on when the output falls below the threshold and off when the current reaches the limit or the output recovers, so the rate varies with input, output and inductance. The document states the family runs between 2 MHz and 3 MHz depending on the member, with variation inside each part. For an emissions measurement that is a spread, not a single line, and the filter has to be sized for the lowest rate in the band.
The 135 ns minimum on time is the constraint at high input. From a 4.2 V cell to a 1.1 V rail the duty cycle is 26 per cent, which at 2 MHz is 130 ns, right at the limit. A part asked to hold 1.1 V from a 5 V adapter will hit the minimum on time and start to skip cycles, which raises the ripple and the effective frequency. The input range is 6 V on paper and about 4.5 V in practice for this output voltage.
Where this part fits
Processor and FPGA core rails, sensor hubs, memory supplies in wearables and any board that has to make 1.1 V from a single lithium cell in a footprint under 1.5 mm by 1 mm. Our desk keeps the cross reference for the TPS6223xx family and the marking list that separates the nineteen voltage options, see power management cross reference and pin to pin cross reference.
What to check before a purchase order
Check the four characters of the order code against the voltage table. TPS622311 is 1.1 V at 2 MHz, TPS622313 is 1.3 V at 3 MHz, TPS622315 is 1.15 V at 2 MHz and TPS622318 is 1.25 V at 3 MHz, and they share one document and one body. A reel picked by the first six characters will put the wrong voltage on the board, and the fault will look like a core that will not boot rather than a purchasing error.
Check whether the board relies on the enable and mode pins being terminated. This member has no internal pull down, so both pins need a defined level at all times, including during power up before the processor drives them. A board that leaves them to a processor port that is high impedance at reset will switch between modes as the pin floats. See incoming inspection plan for the marking and reel check on a 1.45 mm by 1.00 mm body.
Questions that come up on this part
Can the 1.1 V option be replaced by the adjustable member, is a common question during a shortage. The TPS6223xx family is fixed voltage only, so there is no adjustable fallback in the same body, and the substitute has to come from a different family with a different footprint. That is worth knowing before the reel runs out rather than after.
The second question is about the 2 per cent output accuracy against a core that wants 1 per cent. The 2 per cent figure covers line, load and temperature for the whole family, and on a 1.1 V rail it is 22 mV. A core that cannot accept that needs a different class of converter, and a core that can accept it should not be given a tighter specification on the purchase order than the device can hold.