TPS62201DBVR
Product Specifications
TPS62201DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62201DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62201DBVR: 2.5 V to 6 V, 300 mA step down converter with a fixed 1.8 V output
TPS62201DBVR is a small synchronous buck with the feedback divider inside the package and a fixed output voltage in a SOT-23 body of 5 pins. It is the fixed 1.8 V member of a family that has been in production for two decades, and it exists because a 1.8 V rail from a lithium cell or a 3.3 V rail is a five part problem, not a converter project.
Order code and package
| Order code | TPS62201DBVR, DBV package, 3000 pieces on a large reel |
| Body | SOT-23, 2.9 mm by 1.6 mm, five pins, no exposed pad |
| Output | Fixed 1.8 V, the divider is internal and there is no feedback pin |
| Family | TPS62200 is the adjustable member, the other suffixes are fixed at 1.2 V, 1.5 V, 2.5 V and 3.3 V |
| Control | Synchronous buck with a fixed off time loop and automatic power save at light load |
| Rating | 300 mA output, -40 C to 85 C ambient |
Electrical parameters that decide the application
| Input range | 2.5 V to 6 V operating, under voltage lockout between 1.5 V and 2 V |
| Output current | 300 mA rated, P channel current limit 380 mA minimum and 480 mA typical |
| Switches | P channel 530 mOhm typical and 690 mOhm maximum, N channel 430 mOhm typical and 540 mOhm maximum |
| Switching frequency | 1 MHz typical, 650 kHz to 1500 kHz across parts and conditions |
| Quiescent current | 15 uA typical and 30 uA maximum while not switching, 0.1 uA typical in shutdown |
| Efficiency | Up to 95 per cent at 3.6 V in and 1.8 V out |
| Accuracy | Within 3 per cent over the temperature range, which is the internal reference window |
| Soft start | Internal ramp, no external parts |
| Thermal | 220 C/W junction to ambient in the five pin SOT-23 body |
| Protection | P channel current limit, thermal shutdown, no power good output |
Family variants and how they differ
| TPS62200 | the adjustable member of the family, same body, a divider on the feedback pin instead of a fixed output |
| TPS62202 and TPS62203 | fixed 1.5 V and 1.2 V versions of the same die in the same footprint |
| TPS62207 and TPS62208 | fixed 2.5 V and 3.3 V versions, for a rail above 1.8 V |
| TPS562212 | 2 A from 18 V in an eight pin body, a much larger converter for a heavier load |
| TPS62130 | 3 A from 17 V in a QFN, for a rail that needs more than 300 mA |
Points to check before this part goes on a BOM
A fixed output removes the divider and with it the divider tolerance, but it also removes the ability to trim. The 3 per cent window is the internal reference and includes the temperature drift, so a 1.8 V rail can sit at 1.746 V or 1.854 V and still be inside the specification. A load that needs 1.8 V within one per cent has to use the adjustable member of the family and one per cent resistors.
The 300 mA rating and the 380 mA minimum current limit leave only 27 per cent of margin. With a 2.2 uH inductor and 1 MHz switching the ripple at 1.8 V out is modest, but a load step that charges a large output capacitor or a small inductor that saturates will reach the limit and the output will fold back rather than hold. This is a 300 mA part for a load that is genuinely under 300 mA, not a 300 mA part with headroom.
The switching frequency spread is the parameter that catches second sources and inductor choices. The typical is 1 MHz but the guaranteed window runs from 650 kHz to 1500 kHz, so the inductor has to be rated for saturation at the low end and the output ripple has to be acceptable at the low end as well. An inductor chosen against 1 MHz alone can be half the value it should be at 650 kHz.
The 220 C/W thermal resistance of the five pin SOT-23 is the real limit on the current. At 300 mA from 3.6 V to 1.8 V with 90 per cent efficiency the dissipation is about 60 mW, which is a 13 C rise, so the part is comfortable. At 500 mA the dissipation triples and the rise approaches 40 C, which is why the 300 mA rating is not conservative, it is the point where the body still has margin at 85 C ambient.
The under voltage lockout between 1.5 V and 2 V is wider than the 2.5 V minimum input suggests, and it matters for a 2.5 V rail. A 2.5 V rail at minus twenty per cent is 2.0 V, which is the top of the lockout window, so a rail that sags on a load step can shut the converter down in the middle of the transient. A board running at the bottom of the input range should measure the sag, not just the nominal.
The family covers 1.2 V to 3.3 V in the same five pin footprint, which is both convenient and a trap. A board that changes its rail from 1.8 V to 3.3 V changes only the suffix and the inductor, and the same footprint can be reused, but the 3.3 V member cannot be operated from a 3.6 V input with any margin because the part needs the input above the output plus the drop. Every suffix has its own input floor.
There is no power good output and no enable divider, only an enable pin with a 1.3 V high threshold and 0.1 uA of leakage, which is what allows the part to be driven from 1.8 V logic. A system that needs to know the rail is valid has to use a supervisor or the ADC on the processor, and a system that needs a delayed start has to add an RC on the enable pin rather than rely on the converter.
The part runs at 100 per cent duty when the input approaches the output, so it behaves as a switch with the P channel resistance in the path. At 300 mA and 530 mOhm that is a 160 mV drop, which means a 1.95 V input gives 1.79 V out at full load and the loop is out of regulation. A rail specified at 1.8 V from a 2.5 V minimum input has more margin than the headline suggests, but a rail from a 1.9 V source does not.
Shutdown current of 0.1 uA typical is the reason this part survives in battery products, and the 15 uA quiescent current is what allows it to stay enabled in a standby state where the processor is asleep. The two figures are the whole argument for a synchronous buck over an LDO at 1.8 V from 3.6 V, where an LDO would dissipate 540 mW at 300 mA and this part dissipates 60 mW.
Where this order code fits
It belongs in a small battery powered product, a hand held terminal, a sensor node or a set top box accessory, where a 1.8 V rail feeds a microcontroller, a memory device or an analog block at 300 mA or less. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Reduce Component Cost page.
Questions buyers ask
Can the output be adjusted? Not on this suffix. The divider is internal and the output is fixed at 1.8 V. The TPS62200 in the same footprint is the adjustable member of the family.
What inductor should be used? One rated for the 650 kHz low end of the frequency window and for at least 500 mA of saturation, so that the ripple at the low end of the range stays inside the current limit.
Is it a drop in replacement for the 3.3 V version? Same body and pin out, but the input floor changes with the output. A 3.3 V output needs an input above 3.3 V plus the drop, so a 3.6 V rail is the minimum in practice.
What is the real current limit? 300 mA is the rating and the P channel limit is 380 mA minimum. A load that draws within 20 per cent of 300 mA should be checked on the bench with the chosen inductor.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.