TPS62180YZFR
Product Specifications
TPS62180YZFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62180YZFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62180YZFR: dual phase 6 A step down for 12 V and three cell rails
TPS62180YZFR is a synchronous two phase step down converter in a DSBGA body of 24 pins. Two current balanced phases of 3 A each switch out of phase, so the input capacitor sees roughly half the ripple a single phase would give it and the two inductors stay low enough for a tablet, a blade server or a solid state drive bay. The input window of 4 V to 15 V covers a three cell lithium pack and a regulated 12 V rail, and the output is set anywhere from 0.9 V to 6 V with an external divider.
Order code and package
| TPS62180YZFR | active, production, DSBGA 24 pins, 3000 pieces on a large reel |
| TPS62180YZFT | same die and same marking on a 250 piece small reel for prototype builds |
| Body and marking | 2.10 mm by 3.10 mm, 0.5 mm ball pitch, marking ELC180 |
| Moisture level | Level 1, 260 C, unlimited floor life |
| Temperature | minus 40 to 125 C junction |
| Ball material | SNAGCU, RoHS Yes |
Electrical parameters that decide the application
| Input voltage | 4 V to 15 V operating, lockout at 3.7 V on a falling input |
| Output current | 6 A continuous, split as 3 A on each phase |
| Output voltage | 0.9 V to 6 V adjustable on the TPS62180 |
| Reference | 0.8 V nominal, 0.792 V to 0.808 V window |
| Accuracy | plus or minus 1 per cent in PWM mode at 25 C |
| Switch resistance | 27 mOhm high side typical and 65 mOhm maximum, 21 mOhm low side typical |
| Current limit | 4.0 A to 5.5 A per phase with 7.5 V in |
| Phase delay | 250 ns fixed between phase one and phase two |
| Quiescent current | 28 uA typical, 55 uA over minus 40 to 85 C |
| Power good | asserts at 94 to 98 per cent rising, releases at 90 to 94 per cent falling |
Family variants and how they differ
| TPS62182 | same body, same pinout, fixed 3.3 V output instead of a divider |
| TPS62184 | pin to pin compatible sibling with a different current split |
| AEE | efficiency enhancement that shifts the operating point across the duty cycle |
| 100 per cent mode | both high side switches held on when the input falls to the output |
| Hiccup | retry after a short circuit rather than a latch, with a 4.7 ms off time |
| Discharge | 60 Ohm output discharge when the enable pin goes low |
Points to check before this part goes on a BOM
The 6 A figure is a two phase number. Each phase carries 3 A and the 4.0 A to 5.5 A current limit window belongs to one phase, so a board that pulls uneven current from the two outputs through an unbalanced divider reaches the floor of the loaded phase long before the pair is anywhere near 6 A total.
Duty cycle is not the restriction here. The part runs to 100 per cent duty with no minimum off time even at the lowest output setting, which is what allows a 0.9 V rail to stay in regulation from a 4 V input with the high side switch held on and both inductors carrying direct current.
The 1 per cent accuracy applies to PWM mode. Power save widens the window to 2 per cent at 3.3 V and 1.8 V, and to 3 per cent on the fixed 3.3 V member, so a rail that has to hold 1 per cent at ten microamps has to be forced out of power save by loading it or by keeping the mode pin from idling.
The reference window of 0.792 V to 0.808 V is wider than the 1 per cent headline. A divider calculated from 0.800 V exactly can sit 1 per cent high or low before the resistor tolerance is added, and the divider current then sets how much that error moves with the feedback leakage of 100 nA.
Lockout falls at 3.7 V although the guaranteed operating range starts at 4 V. The data sheet note says the 4 V floor is not violated by the lockout and hysteresis windows, which means a 3.8 V rail is outside the specification even though the part keeps switching on it.
The 250 ns phase shift is fixed in silicon. Ripple cancellation at the input depends on the two inductors matching in value and in saturation behaviour, so a pair taken from different batches gives less benefit than the phase relationship suggests.
Hiccup retries instead of latching. A load with a large input capacitance can hold the part in hiccup while that capacitance charges, so the 4.7 ms off time and the soft start capacitor decide whether the rail ever comes up into a heavy load.
Two rails from one part
The two phases are balanced in current but they are not independent outputs. A board that needs 5 V at 2 A and 1.8 V at 4 A needs two parts, not one, because both phases share one feedback node on the adjustable member. Treating the second phase as a spare rail is the most common mistake made with this family.
Where two real rails are wanted, the pin compatible TPS62184 splits the phases differently and the two devices share a board footprint, so a build that starts on one and moves to the other does not need a new board revision.
Sizing the inductors and the output capacitor
A 1 uH inductor per phase with 22 uF at the input and 47 uF at the output is the combination the vendor uses in its own application curves at 3.3 V and 6 A. Going below 1 uH raises the ripple until the phase current limit is reached at a lower average load, which quietly removes the 6 A rating.
The output capacitor figure is quoted as two or four pieces of 47 uF depending on the output voltage, because power save accuracy is tied to output ripple. A single 22 uF ceramic on a 0.9 V rail will meet the loop but miss the 1 per cent window in power save.
Where this order code fits
The part is bought for low profile point of load rails in computing, networking and battery powered equipment where height is the binding constraint rather than current. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Is 6 A available from a 5 V input? Yes at 3.3 V out, because the duty cycle is high and both phases conduct most of the period. At 5 V in and 5 V out the part is in 100 per cent mode and the current is limited by the inductor resistance and the switch resistance, not by the control loop.
What sets the switching frequency? An internal off time generator tied to the input and output voltages. There is no external resistor, and the frequency moves with the operating point, which is why the efficiency curves are drawn against input voltage rather than against a fixed frequency.
Can the two phases be paralleled into one 6 A output? That is what they already are. Both phases feed one output node, which is why the current limit is quoted per phase and the total is the sum of the two windows.
Does the part need a minimum load? No. It enters power save and reduces the switching frequency, and the output stays in regulation. The penalty is accuracy and ripple, not dropout.
What happens on a shorted output? Hiccup. The part stops switching, waits 4.7 ms, restarts with soft start, and repeats until the short is removed, which keeps the die temperature inside the thermal shutdown window.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.