TPS62177DQCR
Product Specifications
TPS62177DQCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62177DQCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62177DQCR fixed 3.3 V at 500 mA from a 4.75 V to 28 V input
The TPS62177DQCR is the fixed 3.3 V member of the TPS6217x pair, a synchronous buck that takes 4.75 V to 28 V in and delivers 500 mA from a 10 pin WSON body of 3 mm by 3 mm. The headline is not the current, it is the quiescent behaviour: 4.8 microamp typical in sleep mode with the SLEEP pin low, against 22 microamp typical in normal operation, and 1.5 microamp in shutdown. A 28 V input converter that idles at 5 microamp is a different class of part from the 12 V converters that dominate the small buck market.
High side on resistance is 850 milliohm typical and 1430 milliohm maximum at 6 V input, low side 320 milliohm typical and 530 milliohm maximum, which is what a 28 V rated device looks like: the FETs are small and the voltage rating is high, so the part is built for efficiency at light load rather than for 500 mA at full current with margin. The reference is 0.8 V, the switching rate is 1 MHz typical, and the device holds 100 per cent duty cycle so it can pass a sagging input through to the load without a second stage. Thermal shutdown is at 150 degrees junction.
The SLEEP pin is the second half of the story. With SLEEP low the part runs in a reduced bias state that delivers up to 15 mA at 3.3 V, which is enough to keep a real time clock, a wake circuit or a memory retention rail alive while the rest of the board is off. Above that load the converter has to come back to normal operation, and the pin is the signal for that. The output is also actively discharged when the part is disabled, and a power good output reports the rail.
Key parameters from the SLVSB35C document
| Input range | 4.75 V to 28 V, for multi cell packs and 12 V or 24 V rails |
| Output | 3.3 V fixed on this member, 500 mA rated, adjustable 1 V to 6 V on the TPS62175 |
| Switching frequency | 1 MHz typical, with 100 per cent duty cycle mode at dropout |
| Quiescent current | 22 microamp typical and 36 microamp maximum in normal operation, 4.8 microamp typical in sleep mode |
| Sleep mode current | 4.8 microamp typical and 10 microamp maximum, with 15 mA of output available |
| Shutdown current | 1.5 microamp typical and 5 microamp maximum with the enable pin low |
| High side resistance | 850 milliohm typical and 1430 milliohm maximum at 6 V input |
| Low side resistance | 320 milliohm typical and 530 milliohm maximum at 6 V input |
| Reference | 0.8 V internal, with 100 nA maximum leakage at the feedback pin |
| Sleep accuracy | 2 per cent typical and 2.9 per cent maximum at 3.3 V out in sleep mode |
| Protection | Thermal shutdown at 150 degrees junction, active output discharge when disabled |
| Package | 10 pin WSON, 3 mm by 3 mm, DQC body with exposed thermal pad |
Why 28 V input and 5 microamp standby belong in one part
Industrial and telecom boards usually carry a 24 V or 48 V bus and need a 3.3 V housekeeping rail that stays alive when the rest of the board is off, because a supervisor, a real time clock or a wake receiver has to keep running. The usual answer is two converters: a wide input buck for the working rail and a separate always-on regulator for the standby rail. This part collapses that into one device, because it can run from the bus directly and drop into a 4.8 microamp state on command.
The cost of the wide input range is conduction loss. A 850 milliohm high side FET at 500 mA drops 0.42 V, and at 3.3 V out from 24 V in the duty cycle is 14 per cent, so the high side conducts briefly but the low side carries the current for the rest of the period at 320 milliohm. The loss is real but the part is not asked for 2 A, it is asked for half an amp and a low idle current. Judged on that, the resistance numbers are the right trade.
The active discharge matters in a standby rail more than in a general purpose one, because a rail that is switched off and then on again during a wake cycle has to come back to a known state. Without discharge the 3.3 V node holds its charge into the load for hundreds of milliseconds, and a processor that is released before the rail is gone will start from an undefined state. The discharge switch removes that question.
Where this part fits
24 V industrial buses, telecom line cards, battery backed instruments, building controllers and any board where a 3.3 V housekeeping rail has to idle in microamps and wake on a signal. Our desk keeps the cross reference for the wide input family and the second source notes, see power management cross reference and how to verify a drop in replacement.
What to check before a purchase order
Check the sleep mode load against the 15 mA figure. A board that expects the standby rail to carry a 40 mA receiver in sleep mode will find the rail dropping out of regulation, and the fix is either to raise the SLEEP pin during that interval or to move the receiver to the main rail. The 15 mA number is a hard limit, not a suggestion.
Check the leakage of everything else on the standby rail. A 4.8 microamp quiescent current is meaningless if the divider or the supervisor on the same node leaks 20 microamp, and a 100 kilohm divider across 3.3 V alone draws 33 microamp. The standby budget has to be computed across the whole node rather than read off the converter page. See incoming inspection plan for the receipt check on a 10 pin WSON with an exposed pad.
Questions that come up on this part
Can the part run from a 48 V bus, is a question that arrives on telecom boards. The recommended ceiling is 28 V, so a 48 V bus needs a pre regulator or a different device, and the absolute maximum is not a margin to plan against. A 36 V nominal bus with transients is also outside the recommended range once the transients are counted.
The second question is why the sleep mode current is only specified at 3.3 V out. The bias circuits scale with the output voltage, and the accuracy in sleep mode is quoted as 2 per cent typical against 1 per cent in PWM, so the mode is intended for retention rather than for precision. A rail that has to hold 1 per cent while idling at microamps is not what this mode is for.