Contact Us

TPS62173DSGR

Brand: Texas Instruments
Texas Instruments TPS62173DSGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62173DSGR — Power Management & Signal Chain | Superb Automation

TPS62173DSGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62173DSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62173DSGR: 5.0 V fixed, 0.5 A step down converter in a 2 mm by 2 mm WSON body

TPS62173DSGR is a fixed 5.0 V synchronous buck that takes a 12 V rail or a lithium pack down to 5 V with a 17 uA quiescent current and no external compensation in a WSON body of 8 pins. It runs from 3 V to 17 V, delivers 0.5 A at a fixed 5.0 V, and switches at 2.25 MHz from a small inductor. Quiescent current is 17 uA typical and 25 uA maximum, shutdown current is 1.5 uA typical, and the 8 pin body is 2 mm by 2 mm with a power good output and a 100 per cent duty cycle mode for the lowest dropout.

Order code and package

TPS62173DSGR8 pin WSON (DSG), 2.00 mm by 2.00 mm, 3000 pieces on a large reel, marking QUE, moisture level 2 with a one year floor life
TPS62173DSGTsame body and silicon, 250 pieces on a small reel
TPS62173DSGRG4same part with the green material declaration, 3000 pieces on a large reel
Output voltage5.0 V fixed on this member, with the same die available as the adjustable TPS62170 and the fixed 1.8 V TPS62171 and 3.3 V TPS62172
Operating temperatureminus 40 C to plus 125 C junction

Electrical parameters that decide the application

Input voltage3 V to 17 V operating, with the part still functional down to the lockout
Output voltage5.0 V fixed, from a family that covers 0.9 V to 6 V
Output current0.5 A continuous, and 0.5 A is also the practical ceiling of the 8 pin body
Switching frequency2.25 MHz typical, which is what allows a 2.2 uH inductor
Quiescent current17 uA typical and 25 uA maximum in power save mode, 1.5 uA typical in shutdown
High side on resistance300 mOhm typical and 600 mOhm maximum at 6 V or above, rising at 3 V in
Current limit0.85 A minimum, 1.05 A typical and 1.35 A maximum on the high side FET
Power goodopen drain, 95 per cent rising and 90 per cent falling of the nominal output, sinking 2 mA
Undervoltage lockout2.6 V minimum, 2.7 V typical and 2.82 V maximum rising, with 180 mV of hysteresis
Soft startinternal ramp of about 1 ms, with the output rising monotonically into a pre biased load

Family members and the pins that matter

TPS62170adjustable from 0.9 V to 6 V with a 1.2 V feedback reference, the member to specify when the rail is not one of the fixed values
TPS62171 and TPS62172fixed 1.8 V and 3.3 V, same body and same external components apart from the feedback divider
FB pin on fixed versionstied to ground for better thermal performance, which is why a fixed member cannot be turned into an adjustable one with a resistor
PG pinopen drain and useful for sequencing a second rail, with thresholds at 95 per cent up and 90 per cent down
DCS-Control loopno external compensation, stable across the ceramic output capacitor range in the vendor table
Pin compatibilitythe same footprint as the TPS62160 and TPS62125, so a board can be re populated without a change

Points to check before this part goes on a BOM

The 17 uA quiescent current is the reason this family exists, and it is a power save mode figure. Forcing the part into continuous conduction, which happens as soon as the load rises above the power save threshold, raises the current to the operating value in the electrical table. A product that sits at 20 mA of load most of the time is not at 17 uA, it is at whatever the switching losses dictate, and the efficiency curve at 20 mA is the honest number.

The 2.25 MHz switching frequency is high for a 17 V part and it is what makes a 2.2 uH inductor and a 10 uF output capacitor enough. It also means the switching loss is a larger share of the total at light load, which is exactly why the part drops into power save mode and skips cycles instead of holding the frequency. A customer who needs a clean spectrum has to accept the higher quiescent current that comes with forced PWM.

The 5.0 V fixed output is set internally and the feedback pin is tied to ground, which the vendor recommends for thermal reasons. That also means the rail cannot be trimmed. A product that needs 5.1 V for a cable drop has to use the adjustable TPS62170 and a divider, and the two parts are otherwise the same silicon in the same body.

The current limit window runs from 0.85 A to 1.35 A on a 0.5 A part. That is a wide window and it is deliberate, because the limit protects the inductor and the FET rather than the load. A shorted output pulls somewhere between those two figures for as long as the thermal protection allows, and the 160 C junction limit is what ends the event. Fusing a 0.5 A rail against the minimum of the window is the conservative choice.

Undervoltage lockout at 2.82 V maximum rising is high for a part that claims a 3 V minimum input. There is only 180 mV between the lockout ceiling and the bottom of the operating range, so a 3.0 V rail that sags during a load step can drop the converter out. On a lithium cell at the end of discharge this is the behaviour that shows up as a reset, and the fix is a higher input rail rather than a different capacitor.

The power good thresholds of 95 per cent up and 90 per cent down are wide, and the pin sinks 2 mA, which is enough to drive a small indicator or a logic input directly. The open drain output needs a pull up and the vendor suggests one to the output rail, which is convenient because the signal then tracks the rail it is reporting. A pull up to a different rail needs a level check.

The pin compatibility with the TPS62160 and TPS62125 is a production convenience rather than an electrical one. The three parts have different current ratings and different quiescent currents, and a board that accepts any of them will pass a functional test with all three while meeting the standby budget with only one. The part number on the reel is the only reliable evidence.

Where this order code fits

It takes a 12 V intermediate rail down to 5 V for logic, sensors and USB charging paths in industrial controllers, cameras, modems and embedded boards, and it does the same job from a three cell lithium pack where the input drifts between 9 V and 12.6 V. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Can it deliver 0.5 A from 12 V in? Yes, with the caveat that the 8 pin WSON body has to get rid of about 300 mW at full load. On a board with a ground plane under the part that is comfortable, on a two layer board with a narrow trace it is not.

Why is the quiescent current 17 uA in one place and higher elsewhere? 17 uA is the power save mode figure at no load. Once the load is high enough to keep the converter in continuous conduction, the operating current applies. Read the efficiency curve for the load the product actually draws.

Can the 5.0 V output be adjusted? Not on this order code. The feedback pin is grounded internally on the fixed members. Use the TPS62170 for an adjustable rail.

What happens below the 3 V input minimum? The converter keeps working down to the 2.7 V typical lockout and stops switching below it. Between 2.82 V and 3 V the behaviour depends on the part, so the operating range rather than the lockout is the number to use.

Does it need an external compensation network? No. The DCS-Control loop is internally compensated and stable with the ceramic output capacitors in the vendor table.

Is a power good signal available? Yes, open drain, 95 per cent rising and 90 per cent falling, sinking 2 mA. It is useful for sequencing a second rail without an external supervisor.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.