TPS62152RGTR
Product Specifications
TPS62152RGTR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62152RGTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62152RGTR fixed 3.3 V at 1 A from a 3 V to 17 V input
The TPS62152RGTR is the 3.3 V member of the TPS6215x family: 3 V to 17 V input, 1 A output, 2.5 MHz DCS-Control, in a 16 pin VQFN of 3 mm by 3 mm. The output is fixed through an internal divider, so there is no FB node on the board and no divider tolerance to add to the reference. The family table lists the 62151 at 1.8 V, this part at 3.3 V, the 62153 at 5.0 V, and the 62150 and 62150A as the adjustable members, with the A version driving the power good pin low while the enable is low where the plain version leaves it high impedance.
High side on resistance is 90 milliohm typical and 170 milliohm maximum at 6 V input, the static current limit is 1.4 A minimum, 1.7 A typical and 2.2 A maximum, and the reference is 0.8 V. Quiescent current is 17 microamp with the enable high and no load, shutdown current is 2.6 microamp typical, thermal shutdown is at 160 degrees junction, and the DEF pin still shifts the output by about 5 per cent above nominal when it is tied to the output rather than to ground.
One amp is the point of this family. A 1 A converter in a 3 mm by 3 mm body with a 17 V ceiling covers the rail that feeds a CAN transceiver, a sensor cluster, an analog front end or a small processor core, and it does so with a 2.2 microhenry inductor and a 10 microfarad output capacitor. The 2.5 MHz carrier keeps those parts small, and the 17 V rating means the same device works on a 12 V rail, a 15 V rail and a 24 V rail within its derated window.
Key parameters from the SLVSAL5E document
| Input range | 3 V to 17 V, functional down to the undervoltage lockout |
| Output | 3.3 V fixed on this member, 1 A rated |
| Reference | 0.8 V internal, with the DEF pin shifting the setting by about 5 per cent |
| Switching frequency | 2.5 MHz nominal, 1.25 MHz selectable through the FSW pin |
| High side resistance | 90 milliohm typical and 170 milliohm maximum at 6 V input |
| Current limit | Static high side limit 1.4 A minimum, 1.7 A typical and 2.2 A maximum |
| Quiescent current | 17 microamp with the enable high and no load in power save mode |
| Shutdown current | 2.6 microamp typical with the enable pin low |
| Control pin leakage | 0.01 microamp typical and 1 microamp maximum on EN, DEF and FSW |
| Thermal shutdown | 160 degrees junction with hysteresis |
| Power good | Open drain, high impedance while the enable pin is low on this member |
| Package | 16 pin VQFN, 3 mm by 3 mm, RGT body |
The current limit is the number to check, not the 1 A rating
The static limit is 1.4 A minimum and 2.2 A maximum, which is a wide window and a narrow margin over the 1 A rating. At the minimum end a rail that is asked for 1.2 A on a hot day will current limit before it reaches the load, and at the maximum end a short circuit will push 2.2 A through an inductor that was picked for 1 A. The inductor saturation current has to be above 2.2 A, not above 1 A, and the trace width has to carry the same number for the few microseconds before the protection reacts.
The propagation delay makes it worse. The static limit is a steady state figure, and the document notes that the current can be higher during the internal delay, so a hard short can reach well above the 2.2 A ceiling for a short interval. A 2 A saturation part is not adequate; a 2.5 A to 3 A part costs a few cents more and removes the margin question entirely.
On the other side, 1 A in a 3 mm by 3 mm body at 2.5 MHz is a modest thermal load. From 12 V to 3.3 V the duty cycle is 28 per cent, the high side conducts for less than a third of the period, and the loss is dominated by the low side FET and the inductor. A two layer board with a reasonable copper island under the pad handles it without a thermal via array.
Where this part fits
3.3 V rails on 12 V and 24 V industrial boards, sensor supplies, CAN node power, small processor cores and analog front ends that draw up to an amp. The fixed output and the small body make it a natural fit behind a front end converter where the rail is a housekeeping supply rather than the main load. Our desk keeps the cross reference and the drop in notes for the TPS6215x family, see power management cross reference and pin to pin cross reference.
What to check before a purchase order
Check the voltage suffix on the reel, not the family name. Five parts share one document and one body, and the fixed members differ only in the internal divider, so a reel picked by family name will produce a board that comes up at 1.8 V or 5 V and looks like a feedback fault to anyone debugging it.
Check the power good polarity requirement against the family table. If the board expects PG to be driven low while the rail is disabled, the A member is the correct part, and the plain part will leave the pin high impedance. Check the FSW strap as well: the pin selects between 2.5 MHz and 1.25 MHz, and the inductor and the output bank have to match the chosen rate. See incoming inspection plan for the receipt check on a 16 pin VQFN.
Questions that come up on this part
Can the 1 A part be pushed to 1.5 A for a short burst, is a question that arrives with most 1 A converters. The static limit at its minimum end is 1.4 A, so a burst above that will hit the limit, and the output will droop rather than deliver. The honest answer is to use the 3 A member of the same family, which shares the body and the pinout and costs little more.
The second question is about the DEF pin. Tied to ground the part regulates to 3.3 V, tied to the output it regulates about 5 per cent above, which is 3.46 V. That is a way to compensate a cable drop to a remote sensor, and it is not a way to get 5 V out of a 3.3 V part. The family table is the reference for which member does what.