TPS621361RGXR
Product Specifications
TPS621361RGXR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS621361RGXR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS621361RGXR 4 A at 1 MHz from 3 V to 17 V with hiccup protection
The TPS621361RGXR is the 1 MHz member of the TPS62136 family and the twin of the TPS62135 in everything except switching rate and two features. It takes 3 V to 17 V in, delivers 4 A, uses the same 0.7 V reference and the same 11 pin VQFN of 3 mm by 2 mm, and carries hiccup overcurrent protection with no active output discharge. Where the 2.5 MHz members of the family are built for a small inductor, this one is built for a 12 V input where switching loss dominates and a larger inductor is available.
High side resistance is 100 milliohm typical and 180 milliohm maximum at 4 V input, the static current limit window is 4.8 A to 6.5 A with a 1.5 A negative limit, quiescent current is 18 microamp typical and 46 microamp maximum at 85 degrees junction, and shutdown current is 1 microamp typical. The output is set from 0.8 V to 12 V through the FB2 divider, and the VSEL pin allows a selection between a resistor set voltage and a second divider node. DCS-Control keeps the loop stable without external compensation and hands over to power save mode without a discontinuity.
The single number that separates this device from the TPS621351 is the carrier. At 1 MHz the on time for a 3.3 V output from a 12 V input is about 275 ns, where the 2.5 MHz member needs 110 ns, and that headroom is worth real efficiency at high input voltage because the high side FET conducts for the same duty cycle but is turned fewer times per second. The bill is a larger inductor and a larger output capacitor for the same ripple.
Key parameters from the SLVSDV2 document
| Input range | 3 V to 17 V, aimed at 12 V rails and multi cell lithium packs |
| Output current | 4 A, with the static limit from 4.8 A to 6.5 A and a 1.5 A negative limit |
| Output voltage | 0.8 V to 12 V adjustable against a 0.7 V reference, with the VSEL and FB2 pins for selection |
| Switching frequency | 1 MHz nominal in forced PWM, adapted automatically in power save mode |
| High side resistance | 100 milliohm typical and 180 milliohm maximum at 4 V input |
| Quiescent current | 18 microamp typical and 46 microamp maximum at 85 degrees junction |
| Shutdown current | 1 microamp typical and 8 microamp maximum with the enable pin low |
| Accuracy | 1 per cent in PWM, load regulation 0.05 %/A, line regulation 0.02 %/V |
| Protection | Hiccup overcurrent, thermal shutdown at 160 degrees junction, no active output discharge |
| Soft start | Adjustable through a capacitor on the SS/TR pin, also usable for tracking |
| Package | 11 pin VQFN, 3 mm by 2 mm, RGX body |
| Marking | 621361 on the package top, which is how the 1 MHz part is told from a 621351 at goods inwards |
Choosing 1 MHz over 2.5 MHz
Run the numbers for a 12 V to 3.3 V rail at 3 A. At 2.5 MHz the inductor is about 1.5 microhenry and the ripple is 1.6 A peak to peak, which is over half the load. At 1 MHz the same ripple needs about 3.3 microhenry, and a 3.3 microhenry part in a 4 mm by 4 mm moulded body has roughly half the DC resistance of the 1.5 microhenry part in a 3 mm body. The conduction loss in the inductor falls accordingly, while the switching loss in the FETs falls by the ratio of the frequencies. Both terms move the same way, which is why the 1 MHz members exist at all.
The reverse case is a 5 V to 1.2 V rail at 4 A. There the duty cycle is 24 per cent, the ripple at 1 MHz needs 2.2 microhenry, and a 2.5 MHz part can use 1 microhenry and a smaller capacitor. On a dense board where the rail is 15 mm from the load, that size difference decides whether the converter fits. Frequency choice is a board level decision, and this pair of parts exists so that one board outline can carry either.
There is a third consideration that does not show up in the efficiency table: the minimum on time. At 17 V input and 0.8 V output the duty cycle is under 5 per cent, and at 2.5 MHz that is 19 ns, which is at the edge of what the control loop can deliver without pulse dropping. The 1 MHz member needs 47 ns for the same condition and holds a cleaner waveform at the bottom of the output range.
Where this part fits
12 V and 17 V input rails where 4 A has to be delivered with the highest practical efficiency and a hiccup response to a short, such as industrial controllers, embedded computers, base station housekeeping rails and test equipment. Our desk keeps the family comparison and the second source notes for the 4 A class, see power management cross reference and pin to pin cross reference.
What to check before a purchase order
The marking is the check that matters. Four parts in this family share one body, one pinout and one document: 62135 and 621351 at 2.5 MHz, 62136 and 621361 at 1 MHz, with the discharge and hiccup features split across them. The package top carries the number, and a reel that arrives without it cannot be sorted by measurement alone, because all four regulate correctly and only differ in what they do at a fault and at power down.
Check the inductor against the 6.5 A top of the current limit, and check the output capacitor against the loop stability at 1 MHz with the actual ESR. A part chosen for a 2.5 MHz board and reused at 1 MHz needs the output bank re checked, since the crossover moves with the switching rate even though the loop is internal. See incoming inspection plan for the marking and reel verification we run on this family.
Questions that come up on this part
Can a 621351 be used in place of a 621361 when the reel is short, is the question that comes up in every shortage. Electrically yes, at a higher carrier and a lower inductor value, so the surrounding parts change. Functionally yes, since both carry hiccup and neither discharges the output. The board will pass and the efficiency at 12 V input will drop by the switching term, which is the honest answer rather than a straight yes.
The second question is why the part needs a VSEL pin at all when a divider would do. The pin allows a board to switch between two output voltages without changing components, which is useful for a product that ships in two versions from one assembly, and it allows the output to be set by a resistor to ground or to the output rather than by a full divider pair. The datasheet table is the reference for the two configurations, and neither leaves a node floating.