Contact Us

TPS621351RGXR

Brand: Texas Instruments
Texas Instruments TPS621351RGXR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS621351RGXR — Power Management & Signal Chain | Superb Automation

TPS621351RGXR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS621351RGXR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS621351RGXR 4 A at 2.5 MHz with hiccup current limit

The TPS621351RGXR is the 4 A member of the TPS62135 family, a 3 V to 17 V synchronous buck in an 11 pin VQFN of 3 mm by 2 mm that runs at 2.5 MHz nominal in forced PWM and drops into power save mode at light load when the MODE pin is low. The reference is 0.7 V, the output can be set from 0.8 V to 12 V through a divider, and the high side FET measures 100 milliohm typical and 180 milliohm maximum at 4 V input. The static current limit window is 4.8 A minimum, 5.6 A typical and 6.5 A maximum, and the negative current limit is 1.5 A.

The suffix matters here more than on most parts. The TPS62135 and the TPS621351 share the body, the pinout and the electrical table, and they differ in two features: the 351 carries hiccup overcurrent protection, which turns the converter off for a delay and retries after a short circuit instead of holding a constant current, and it leaves out the active output discharge that the 35 has. On a rail that is disabled and then re enabled in a sequencing test, the difference is visible on a scope: the 35 pulls the output down, the 351 lets it float and decay through the load.

Quiescent current is 18 microamp typical and 46 microamp maximum with the enable high and the part not switching, and shutdown current is 1 microamp typical and 8 microamp maximum. Output accuracy is 1 per cent in PWM, load regulation is 0.05 %/A and line regulation 0.02 %/V, thermal shutdown is at 160 degrees junction, and the package includes a MODE pin that must not be left unconnected because it decides between power save and forced continuous conduction.

Key parameters from the SLVSBH3B document

Input range3 V to 17 V, suitable for multi cell lithium packs and 12 V intermediate rails
Output current4 A, with a static current limit from 4.8 A to 6.5 A and a negative limit of 1.5 A
Output voltage0.8 V to 12 V adjustable against a 0.7 V reference
Switching frequency2.5 MHz nominal in forced PWM, adapted in power save mode
High side resistance100 milliohm typical and 180 milliohm maximum at 4 V input
Quiescent current18 microamp typical and 46 microamp maximum, measured at 85 degrees junction
Shutdown current1 microamp typical and 8 microamp maximum with the enable pin at ground
Accuracy1 per cent in PWM, load regulation 0.05 %/A, line regulation 0.02 %/V
ProtectionHiccup overcurrent on this member, thermal shutdown at 160 degrees junction
Output dischargeNot fitted on the 351, present on the TPS62135 with the same pinout
Configuration pinsMODE for power save or forced PWM, VSEL and FB2 for the output setting, SS/TR for the ramp
Package11 pin VQFN, 3 mm by 2 mm, RGX body

Hiccup protection on a 4 A rail

A constant current limit holds the output at whatever the limit allows while the fault lasts, which means the pass elements and the inductor carry 5.6 A typical into a short until somebody removes it. Hiccup protection does the opposite: it detects the condition, turns the converter off, waits, retries, and if the short is still there it turns off again. The average dissipation in a fault drops by the ratio of the on time to the retry period, which is the difference between a part that survives a harness short and a part that does not.

The cost is behaviour at startup into a heavy capacitive load. A board with a 470 microfarad bank can look like a short on the first attempt, and the hiccup counter will trip before the bank is charged. The SS/TR pin is the fix: a longer ramp keeps the inrush below the limit and lets the converter reach regulation in one pass. A board that adds the output bank without extending the ramp will show a start stop pattern on the bench that gets blamed on the part.

The absence of output discharge changes what happens at power down. With the TPS62135 the rail collapses in a few milliseconds because an internal switch pulls the output to ground. With this part the rail decays through the load, which on a light load can take seconds, and a downstream device that powers up before the rail is gone can be held in an undefined state. If the sequence matters, either use the 35 or add a discharge path.

Where this part fits

12 V intermediate rails that need 4 A at 1.2 V to 5 V, point of load supplies behind a front end converter, solid state drive and embedded computer rails, and any board that wants hiccup protection without an external supervisor. Our desk keeps the family comparison and the substitution notes across the 35 and 351 pair, see power management cross reference and how to verify a drop in replacement.

What to check before a purchase order

Check which of the two features the board depends on. Hiccup and active discharge are mutually exclusive across this pair, and the part number is the only field that tells them apart. A customer who substitutes one for the other to save a lead time will get a working rail and a sequencing fault, in that order.

Check the MODE pin. It is an input, not a strap with an internal pull, and the document says explicitly not to leave it unconnected. A board that lets it float will switch between two behaviours depending on leakage and board cleanliness, which is the kind of fault that survives a bench test and fails in the field. Check the inductor against the 6.5 A maximum of the limit window as well, because hiccup trips on the current, not on the temperature. See incoming inspection plan for the receipt check on an 11 pin VQFN.

Questions that come up on this part

Is 3 V input enough for a 2.5 V output at 4 A, is a question that comes back regularly. It is, but the duty cycle is above 80 per cent, the part spends most of the period in the high side FET, and the 100 milliohm typical resistance sets the drop. At 4 A that is 0.4 V of headroom before the inductor loss, so a 3 V rail feeding a 2.5 V load at full current has almost nothing left. A 3.3 V input is the realistic floor for that combination.

The second question is whether the 1 per cent accuracy in PWM holds in power save mode. It does not: the document notes that the accuracy in power save mode depends on the output capacitor and the ripple, and it can be improved by increasing the output capacitance or reducing the ripple. A rail that has to hold 1 per cent at microamp loads is a forced PWM rail, and the MODE pin is the setting.