TPS62133RGTR
Product Specifications
TPS62133RGTR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62133RGTR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62133RGTR fixed 5 V at 3 A from a 3 V to 17 V input
The TPS62133RGTR is the fixed 5 V member of the TPS6213x family: same 3 V to 17 V input range, same 3 A rating, same 2.5 MHz DCS-Control engine and the same 16 pin VQFN of 3 mm by 3 mm, but with the feedback divider inside the package. There is no FB node to route, no divider to place and no divider error to add to the reference tolerance, which is what a 5 V housekeeping rail actually wants. The family table lists it as 5.0 V output with the power good pin high impedance while the enable pin is low.
The electrical table gives a 0.8 V reference and 90 milliohm typical high side resistance at 6 V input, 170 milliohm maximum, with the static high side current limit in the same 3.6 A to 4.9 A window as the adjustable member. Line regulation is 0.02 %/V, shutdown current is 17 microamp typical with the enable high and no load, and the disable current is 1.5 microamp typical. Thermal shutdown is at 160 degrees junction. With no divider the total error at the output is the reference error plus the internal resistor matching, which is tighter than a 1 per cent external pair in most bills of materials.
The interesting part of this device is the input range against the output. A 5 V output from a 3 V input is not possible in buck mode, so the useful window starts around 5.5 V. From there to 17 V the part covers a 12 V battery that sags, a 12 V rail that is really 13.8 V in a vehicle, and a 9 V or 12 V wall adapter, all with the same components and without a second stage. At the bottom of the window the 100 per cent duty cycle mode takes over and the output follows the input less the resistive drop.
Key parameters from the SLVSAG7F document
| Input range | 3 V to 17 V, with useful operation from about 5.5 V for a 5 V output |
| Output | 5.0 V fixed through an internal divider, 3 A rated |
| Reference | 0.8 V internal, no external FB divider on this member |
| Switching frequency | 2.5 MHz nominal, 1.25 MHz selectable through the FSW pin |
| High side resistance | 90 milliohm typical and 170 milliohm maximum at 6 V input |
| Current limit | High side static limit from 3.6 A minimum to 4.9 A maximum |
| Quiescent current | 17 microamp typical in power save mode with no load |
| Shutdown current | 17 microamp typical and 30 microamp maximum with the enable high, 1.5 microamp with it low |
| Regulation | Line 0.02 %/V at 3 V to 17 V in with a 3.3 V setting, load dependence set by the external parts |
| Power good | Open drain, high impedance while the enable pin is low on this member |
| Thermal shutdown | 160 degrees junction with hysteresis |
| Package | 16 pin VQFN, 3 mm by 3 mm, RGT body |
Why a fixed 5 V member still earns its place
A 5 V rail on an industrial or automotive board is usually a housekeeping supply: a CAN transceiver, a sensor, a relay driver, an isolated converter primary. Those loads do not need trimming and they do not benefit from a divider that adds two components, a noise pickup node and a tolerance term. The fixed member removes all three, and it removes the failure mode where a divider is populated for the wrong rail on a build variant and the output comes up at 3.3 V on a board that expects 5 V.
Mechanically, the part is the same RGT body with the same pin functions apart from FB, which becomes a no connect. That means one board can carry either the fixed 5 V or the adjustable member without a change to the copper, which is useful when a product family has both a 5 V and a 3.3 V variant. The FSW pin still chooses the frequency, the SS/TR pin still sets the ramp, and DEF still shifts the setting by 5 per cent, so the fixed version keeps the flexibility that matters and drops the one that does not.
The 5 per cent shift through DEF is worth knowing about on a 5 V rail. Tied to the output, the part regulates slightly above nominal, which is a way to compensate a long cable drop to a remote load without changing the bill. Tied to ground, it regulates to nominal. It is a pin, not a resistor, so the choice can be made per build.
Where this part fits
5 V housekeeping rails on 12 V and 24 V industrial boards, automotive body controllers, CAN and LIN node supplies, and any board where a 3 A 5 V rail has to survive an input that moves between 6 V and 16 V without a second converter. Our desk keeps the cross reference and the drop in notes for the TPS6213x family, see power management cross reference and pin to pin cross reference.
What to check before a purchase order
Check the output voltage suffix, not the family name. The TPS62133 is 5.0 V, the TPS62132 is 3.3 V, the TPS62131 is 1.8 V and the TPS62130 is adjustable, and all four share the RGT body and the same document. A reel that was picked by family name alone will produce a board that comes up at the wrong voltage and looks like a feedback fault.
Check the input capacitor against the 2.5 MHz carrier and check the inductor against the 4.9 A top of the current limit window rather than the 3 A rating. On a 12 V to 5 V rail at 3 A the duty cycle is 42 per cent, the high side conducts for less than half the period, and the loss is dominated by the low side and the inductor resistance, so a 10 milliohm inductor is worth more than a larger output capacitor. See incoming inspection plan for the receipt check on the reel and the marking.
Questions that come up on this part
Can the output be trimmed to 5.2 V for a cable drop, is a common question. It can be shifted by the DEF pin to about 5 per cent above nominal, which is 5.25 V, and that is the whole range without an external divider. A board that needs a precise trim should use the adjustable member instead.
The second question is whether the fixed version can be substituted for the adjustable one on an existing board. Electrically the pins match apart from FB, which becomes a no connect, but the existing divider would be left floating on the FB pad and the output would come up at 5 V regardless of what the divider was set for. That is a silent change on a board that was built for 3.3 V, so the substitution has to be checked against the board net by net rather than by pin count.