TPS62130AQRGTRQ1
Product Specifications
TPS62130AQRGTRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62130AQRGTRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62130AQRGTRQ1 3 A automotive buck from 3 V to 17 V in a 3 mm by 3 mm VQFN
The TPS62130AQRGTRQ1 is the adjustable member of the TPS6213xA-Q1 family, a synchronous step down converter that takes 3 V to 17 V in and delivers up to 3 A at an output set between 0.9 V and 6.0 V. It sits in a 16 pin VQFN of 3 mm by 3 mm, runs at 2.5 MHz nominal, and is built on the DCS-Control topology, which combines a hysteretic comparator with a voltage mode loop and hands over to power save mode without a glitch at the boundary. The family also carries a 5 V member, the TPS62133A-Q1, and a 1.3 V member, the TPS6213013A-Q1, for boards that do not want a divider.
What separates this part from the industrial TPS62130 is the suffix. All members are AEC-Q100 grade 1 with a minus 40 to 125 degree junction range and are declared functional safety capable with the documentation available to support a safety case. The A in the part number changes the behaviour of the power good pin while the enable pin is low: on the A member the PG output is driven low when the converter is disabled, where the plain part leaves it high impedance. That sounds like a footnote until a downstream regulator is sequenced by PG, because a floating pin reads as good to some logic families.
The static current limit on the high side FET is 3.6 A minimum, 4.2 A typical and 4.9 A maximum, which is a modest margin over the 3 A rating and worth checking against the inductor before the first build. High side on resistance is 90 milliohm typical and 170 milliohm maximum at 6 V input, the reference is 0.8 V, and the part holds 100 per cent duty cycle so it can pass the input rail through when the input falls close to the output.
Key parameters from the SLVSCC2E document
| Input range | 3 V to 17 V, with the part functional down to the undervoltage lockout |
| Output current | 3 A, with a static high side current limit of 3.6 A minimum and 4.9 A maximum |
| Output voltage | 0.9 V to 6.0 V adjustable on this member, fixed 5 V and 1.3 V on the siblings |
| Reference | 0.8 V internal, with 100 nA maximum leakage at the FB pin |
| Switching frequency | 2.5 MHz nominal in forced PWM, 1.25 MHz selectable through the FSW pin |
| High side resistance | 90 milliohm typical and 170 milliohm maximum at 6 V input |
| Shutdown current | 17 microamp typical and 30 microamp maximum with the enable pin high and no load |
| Disable current | 1.5 microamp typical and 25 microamp maximum with the enable pin low |
| Regulation | Line 0.02 %/V quoted at 3 V to 17 V in, 3.3 V out and 1 A |
| Thermal shutdown | 160 degrees junction, with hysteresis before restart |
| Qualification | AEC-Q100 grade 1, functional safety capable, minus 40 to 125 degrees junction |
| Package | 16 pin VQFN, 3 mm by 3 mm, RGT body |
The pins that decide the behaviour
Four pins on this device are configuration rather than connections, and each one has a failure mode if it is left to a default. DEF sets the output voltage programming: tied to ground the part regulates to the divider value, tied to the output it adds 5 per cent to the nominal setting, which is a way to pre bias a rail without changing resistors. FSW chooses between 2.5 MHz and half that rate, and the lower setting is the one to use when the input is a 12 V rail and the efficiency at moderate load matters more than inductor size. SS/TR takes a capacitor that sets the ramp and can also be driven by a signal to make the rail track another supply. EN is the enable, and PG is the open drain output that reports the rail as good.
The 2.5 MHz setting keeps the inductor near 2.2 microhenry for a 3.3 V rail, which is a 3 mm by 3 mm part. Switching to 1.25 MHz doubles the ripple for the same inductance and lets a larger, lower resistance inductor be used, which is the usual choice on a 12 V input where conduction loss in the inductor dominates. There is no external compensation to change at either frequency because the loop is internal, so the choice costs nothing but a strap.
AEE, the automatic efficiency enhancement, drops the switching frequency as the input falls toward the output. On a 12 V rail that never moves it does very little. On a battery rail it is the difference between holding 3.3 V at 3.5 V input and dropping out, because the part can stretch the on time instead of losing regulation.
Where this part fits
Automotive 12 V domains that need 3 A at 3.3 V or 5 V: instrument clusters, camera modules, gateways and infotainment head units, plus any industrial board that wants the same part on a 12 V or 24 V rail without the automotive paperwork. The 17 V ceiling with 100 per cent duty cycle is what makes it usable on a 12 V battery that sags to 8 V during a cold crank without a second stage. Our desk tracks the cross reference for this family and the second source options, see power management cross reference and how to verify a drop in replacement.
What to check before a purchase order
Confirm the power good behaviour against the sequencing plan. If the board expects PG to go low when the rail is disabled, this A member is the correct part; if the board expects a high impedance pin so that a wired or arrangement decides the state, the plain TPS62130 is the correct part. The two are electrically identical in every other respect, which is exactly why the mistake is easy to make and why it shows up only at power down.
Confirm the soft start capacitor against the upstream current budget. A 3 A rail with a large output bank and a short ramp will trip the input supply before the converter reaches regulation, and the SS/TR pin is the only lever on that without adding a load switch. Confirm the inductor against the 4.9 A top of the current limit window rather than the 3 A rating, since a short at the load drives the inductor to the limit before the protection folds the part back. See incoming inspection plan for the goods inwards check on a 16 pin VQFN.
Questions that come up on this part
Does the part really hold regulation at 100 per cent duty cycle, is a question that comes up on every cold crank discussion. It does, but the output sits one drop below the input, set by the high side resistance and the inductor resistance, so a 3.3 V rail fed from a 3.4 V battery will be at 3.25 V rather than 3.3 V at 2 A. The datasheet curve is the number to use, not the headline.
The second question is about the quiescent current in shutdown, which is quoted as 1.5 microamp typical with the enable low. A board that expects a few nanoamps in storage should not use the enable pin as the only switch, because the input capacitors and the leakage of the divider will dominate the measurement anyway.