Contact Us

TPS62050DGSR

Brand: Texas Instruments
Texas Instruments TPS62050DGSR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62050DGSR — Power Management & Signal Chain | Superb Automation

TPS62050DGSR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62050DGSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62050DGSR: 800 mA synchronous step-down converter for a single lithium cell or a 3 to 5 cell battery pack

TPS62050DGSR is an 800 mA synchronous buck converter with a 2.7 V to 10 V input and a 12 uA quiescent current, built around battery powered equipment in a MSOP body of 10 pins. The TPS62050 is part of a family of synchronous step-down converters that take 2.7 V to 10 V in and deliver up to 800 mA, with an adjustable output from 0.7 V to 6 V and fixed options at 1.2 V, 1.5 V, 1.8 V, 2.5 V and 3.3 V. Quiescent current is 12 uA typical, efficiency reaches 95 percent, and the part holds 100 percent duty cycle in dropout with a minimum on time of 100 ns. Accuracy on the fixed output members is minus 3 percent to plus 3 percent across a 0 mA to 600 mA load.

Order code and package

Order codeTPS62050DGSR
Input voltage2.7 V to 10 V
Output current800 mA rated, 600 mA specified
Output voltageadjustable 0.7 V to 6 V, fixed options in the family
Quiescent current12 uA typical
Efficiencyup to 95 percent
Duty cycle100 percent in dropout
Minimum on time100 ns
Package10 pin MSOP with exposed pad
Output accuracyminus 3 percent to plus 3 percent on the fixed members
Line regulation5.2 mV per V
DocumentSLVS432F, September 2002, revised June 2015

Electrical parameters that decide the application

Load regulation0.0045 percent per mA
Switchingsynchronous pulse width modulation, fixed frequency
Shutdown temperature145 C
Input range at the 62056 member3.75 V to 10 V, restricted for the fixed 3.3 V option
High-side resistance0.75 Ohm worst case in 100 percent duty mode at a 3.3 V input
Efficiency at 5 V to 3.3 V93 percent at 300 mA
Efficiency at 3.6 V to 2.5 V93 percent at 200 mA
Enablehigh level turns the part on, low level shuts it down
Bias current at shut downin the microamp range, specified in the electrical table
Thermal paththe exposed pad on the 10 pin MSOP
Referenceinternal, trimmed at the factory
Temperature range-40 C to 85 C ambient

Points to check before this part goes on a BOM

The 100 percent duty cycle mode is what makes this family usable from a battery. When the input falls towards the output the part stops switching and holds the high-side switch on, so the output follows the input down with only the resistive drop across that switch, which is 0.75 Ohm worst case at a 3.3 V input. A battery powered instrument therefore keeps running below its nominal input instead of dropping out.

Twelve microamps of quiescent current is the number to compare when a rail has to sit idle for months. A converter with 100 uA of quiescent current drains 2.4 mAh per day, which is a measurable part of a small cell; at 12 uA the drain is under 0.3 mAh per day, and the difference shows up as shelf life rather than as run time.

The 800 mA rating is the switch rating and the 600 mA figure is where the electrical table specifies the fixed output members. A load that needs 800 mA continuously should be checked against the ripple current and the thermal rise over a real board, because the accuracy columns at 600 mA are the ones the vendor guarantees.

The family structure is worth reading before a substitution. The TPS62056 has a restricted input range because its fixed 3.3 V output cannot be supported below 3.75 V in, while the adjustable member can run down to 2.7 V in. A board built around one member and refilled with another will start but may not hold regulation at the bottom of the input range.

At 1 MHz class switching and 800 mA the inductor is a few microhenries and the output capacitor is ceramic. The document allows a small ceramic output capacitor because the loop is internally compensated, which is what keeps the solution size down; a board that replaces the ceramic with an electrolytic of the same value can see a loop that rings at load step because the equivalent series resistance moved.

The 10 pin MSOP with an exposed pad is a package that a repair line can rework with hot air and no x-ray. That is worth something in instruments that are repaired rather than replaced, and it is one reason this older family is still ordered for service and spare boards after newer parts have moved to smaller bodies.

Efficiency of 95 percent is quoted at a favourable operating point, 5 V in and 3.3 V out at 300 mA. At 2.7 V in and 1.8 V out the switch losses dominate and the figure is lower, so a battery life estimate should be built from the curve at the actual input and load rather than from the headline number.

Where this order code fits

This order code belongs in instruments and portable equipment running from a single lithium cell, a two cell pack or a 3 to 5 cell nickel pack, where the rail is 3.3 V or 2.5 V at a few hundred milliamps and the standby current has to stay in the tens of microamps. Handheld test gear, patient monitors and battery backed industrial sensors are the usual sockets. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Can this part run from a single lithium cell at 3.0 V? Yes. The input range starts at 2.7 V, and below that the part holds 100 percent duty cycle so the output follows the cell down.

Is the output adjustable? The TPS62050 is the adjustable member, set by an external divider from 0.7 V to 6 V.

What is the difference between the members of the family? The fixed output members have restricted input ranges at the higher output voltages, and the accuracy and current figures are specified per member.

SUPERB supplies this order code with date codes and packing on the offer, and the Component Lead Time Solutions page sets out the checks for a battery rail that has to stay in production past the vendor life cycle.