TPS613223ADBVR
Product Specifications
TPS613223ADBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS613223ADBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS613223ADBVR: a 2.0 V fixed boost converter with a 0.75 A peak switch limit and 6.5 uA of quiescent current, for a product that has to run from one alkaline cell
TPS613223ADBVR is a synchronous boost converter that lifts a single cell or a two cell battery to a fixed 2.0 V rail and draws microamps while doing nothing, so a remote sensor or a meter can sit idle for years in a SOT-23 body of 5 pins. The DBV body is five pins on 2.90 mm by 1.60 mm, and the family splits by output voltage rather than by package, with a three pin body of the same footprint available for the fixed rows that do not need an enable pin.
Order code and package
| Catalogue string | TPS613223ADBVR, where 223A is the 2.0 V member of the family and the R letter is the reel row |
| Body | SOT-23, DBV, five pins, 2.90 mm by 1.60 mm, and a three pin DBZ body of 2.90 mm by 1.30 mm exists for other rows |
| Reel | the packaging table prints 250 pieces against the R row and 3000 against the T row for this code, which is the reverse of the convention used by the neighbouring codes in the same table |
| Finish and moisture | NIPDAU plating, moisture level 1, 260 C, unlimited floor life |
| Temperature | minus 40 to 125 C junction, and the tables are written at junction temperature rather than ambient |
| Marking | the DBV rows of this family print 1N4L and 1N5L against the neighbouring codes, so the reel label rather than the body is the reliable identifier |
| Document | SLVSDY5E, January 2018, revised February 2024 |
| Family split | eight fixed outputs from 2.0 V to 5.0 V, four of them in production and two marked Product Preview in the device comparison table |
Electrical parameters that decide the application
| Input range | 0.9 V to 5.5 V, which covers one alkaline cell near the end of its life at 0.9 V and a two cell pack at 3 V |
| Output | 2.0 V fixed in this code, and the family covers 2.0 V, 2.2 V, 2.5 V, 3.0 V, 3.3 V, 3.6 V, 5.0 V in 0.1 V steps within a part |
| Peak switch current limit | 0.42 A minimum, 0.75 A typical and 1.2 A maximum on this member, which is the binding number for how much load the converter can hold at a given input |
| Quiescent current | 6.5 uA typical and 10 uA maximum into the VOUT pin, measured with the output at 1.2 times the target so the converter is in regulation and not in start up |
| Start up | 0.83 V typical and 0.87 V maximum at the output pin with a 250 Ohm load, which is the input level at which the part will begin to boost from a nearly flat cell |
| Accuracy | plus or minus 3 per cent over temperature, quoted against the fixed output rather than against a reference |
| Efficiency | above 90 per cent at a 10 mA load converting 1.5 V to 2.2 V, which is the operating point of a wireless sensor between transmissions |
| Inductor | 0.7 uH to 2.2 uH effective, and 4.7 uH is the value the characteristic curves use for this member |
| Output capacitor | 4.7 uF to 16 uF effective, and the small window is what keeps the part usable in a two component solution |
| Protection | thermal shutdown at 150 C with 20 C of hysteresis, and no current limit beyond the peak switch limit |
| Thermal resistance | 322.2 C per W junction to ambient in the three pin body and 189.7 C per W in the five pin body, which is the number that decides how much current the part can hold in a sealed enclosure |
| Control | hysteretic, so there is no compensation network and the response to a load step is a cycle by cycle decision rather than a loop settling |
The eight fixed outputs and which of them are shippable
| TPS613223A | 2.0 V, 0.75 A typical switch limit, the member on this page |
| TPS61322 | 2.2 V, 0.75 A, the original member of the family |
| TPS613221A | 3.3 V, 1.2 A, for a radio or a sensor that needs a 3.3 V rail from one cell |
| TPS613222A | 5.0 V, 1.8 A, the strongest member, and the one that supports over 500 mA at 5 V from 3 V with an external Schottky diode across the internal rectifier |
| TPS613226A | 3.6 V, 1.2 A, the level that suits a lithium primary cell replacement |
| TPS613224A and TPS613225A | 2.5 V and 3.0 V, both printed Product Preview, so neither is a part to put on a production BOM yet |
Points to check before this part goes on a BOM
The peak switch limit is the real rating, not the output current. At 0.75 A typical the part can hold a few tens of milliamps at 2.0 V from a 1.2 V input and rather more from a 1.5 V input, because the input current in a boost is always higher than the output current by the ratio of the two voltages. A load that draws 200 mA at 2.0 V needs 400 mA from a 1.0 V cell before efficiency is counted, and that sits uncomfortably close to a 0.42 A minimum limit. The arithmetic, not the headline, decides whether this member fits.
The packaging table prints the quantities in a way that has to be read twice. For the 223A code the R row shows 250 pieces and the T row shows 3000, while the 221A and 222A codes in the same table show 3000 against R and 250 against T, and one 222A row appears twice with both numbers. A purchase order copied from a sibling line will ask for the wrong reel. This is worth a line on the offer rather than a discovery at goods inwards.
Two members of the family are marked Product Preview, and that status is not the same as active. The 2.5 V and 3.0 V options are useful levels for a 3 V sensor bus and a lithium cell replacement, and neither is in production. A BOM that needs 2.5 V therefore has to either use the 2.2 V member with a tolerance check or wait, and a quotation that offers the preview part as a normal line is quoting something the vendor does not ship.
The 6.5 uA quiescent current is measured at the output pin with the converter in regulation, which is the honest way to quote it and also the reason it is not the whole story. The feedback divider is internal and fixed, so there is no external resistor pair leaking current, but the inductor and the output capacitor still have leakage and the load still draws whatever it draws. On a sensor that wakes once a minute the average current is dominated by the sleep current of the load, and the converter's contribution is a few percent of the total rather than the headline.
The application circuits in the data sheet show two components, an inductor and a capacitor, and that is the whole external count. It also means there is no soft start capacitor and no compensation to tune, so inrush at start up is set by the peak switch limit and the output capacitor. A 10 uF output capacitor charged from 1.2 V to 2.0 V at a 0.42 A limit needs about 19 us of switch current, which is short enough that the input cell sees a pulse rather than a sag. Where the cell has high internal resistance, that pulse is what pulls the input below the 0.83 V start threshold and makes a unit fail to start on a cold morning.
Thermal resistance of 322 C per W in the three pin body is the reason the five pin body exists for anything above a few tens of milliwatts. At 100 mA out and 2.0 V, with 1.2 V in and 85 per cent efficiency, the dissipation is about 35 mW, which is an 11 C rise in the three pin body and 7 C in the five pin one. Both are acceptable. At 300 mA the dissipation is over 100 mW and the three pin body is at 32 C of rise before the enclosure is considered, which on a 70 C ambient is a part running at 102 C junction.
Sizing a load against the switch limit
Work in input current rather than output current. For a 2.0 V output at 1.2 V input, the ideal input current is 1.67 times the output current, and the real figure is that divided by the efficiency. At 200 mA out the input is about 390 mA, which is inside the 0.42 A minimum limit but only just, and the ripple in the inductor adds to the peak that the comparator sees. A 4.7 uH inductor at 1.2 V in holds the ripple to about 100 mA peak to peak, so the peak sits near 440 mA and the part will current limit on the peaks rather than on the average.
From 1.5 V input the same 200 mA output needs about 290 mA of input current, and the peak is comfortable. That single comparison is why a product that works on a fresh cell can brown out at the end of the discharge, and why the start threshold of 0.83 V is quoted with a 250 Ohm load rather than with a full one.
Why a hysteretic boost suits a battery product
A hysteretic control compares the output against a reference and switches when it falls below, which means the loop is stable without a compensation network and responds to a load step within a cycle. The cost is a switching frequency that changes with the load and the input, so the ripple is not a fixed frequency and an emission scan shows a broad hump rather than a line. For a battery product in a plastic case, that is usually acceptable and the component count matters more.
The other cost is that the output ripple is set by the hysteresis window and the output capacitor rather than by an inductor current ramp. A 10 uF capacitor keeps the ripple small, and a 4.7 uF capacitor at the bottom of the recommended window gives about twice the ripple. On a rail that feeds an analogue sensor, that difference is the one to check on the bench rather than in the data sheet.
Where this order code fits
This is the boost stage in a battery meter, a smoke detector, a thermostat, a portable medical reader or a wireless sensor node, where one cell has to produce a stable rail for a radio that transmits for a few milliseconds a minute Teams comparing it with a neighbouring part start from our Pin to Pin Cross Reference page, and teams replacing a part that has gone end of life start from the Power Management Cross Reference page.
Questions buyers ask
How much current can it deliver at 2.0 V? The limit is the 0.42 A minimum peak switch current rather than an output figure. From 1.2 V in that is roughly 200 mA of output, from 1.5 V in closer to 300 mA, and both fall as the cell discharges.
Does it need a bias supply? No. The part runs from the same input as the inductor and needs only an inductor and an output capacitor.
What is the start threshold? 0.83 V typical at the output pin with a 250 Ohm load, and 0.87 V maximum. Below that the part will not begin to boost even though the operating range starts at 0.9 V on the input.
Which reel do I get with the R suffix? The packaging table prints 250 pieces against the R row for this code and 3000 against T, which is the reverse of the sibling codes, so the reel size belongs on the order and on the acknowledgement.
Is there an enable pin? On the five pin DBV body the enable is a separate pin, so the rail can be turned off completely. The three pin DBZ body has no enable and runs whenever the input is present.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.