TPS613221ADBVR
Product Specifications
TPS613221ADBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS613221ADBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS613221ADBVR: a 3.3 V fixed output boost converter with a 6.5 microamp quiescent current in a five pin SOT-23
TPS613221ADBVR is a synchronous boost converter with a hysteretic control loop, an internal rectifier, a 0.75 A minimum switch current limit and an output voltage set inside the package in a SOT-23 (DBV) body of 5 pins. It runs from 0.9 V to 5.5 V, boosts to a fixed 3.3 V with 3 per cent accuracy over temperature, reaches more than 90 per cent efficiency at 10 mA from a 1.5 V input to a 2.2 V output, limits the switch between 0.75 A and 1.6 A with 1.2 A typical, and draws 6.5 microamp into the output pin while regulating. Packing is 3000 pieces with marking 1N4L.
Order code and package
| TPS613221ADBVR | SOT-23 (DBV) body, 5 pins, 2.90 mm by 1.60 mm, 3000 pieces on a large reel, nickel palladium gold with a tin option, moisture level 1 at 260 C with unlimited floor life, marking 1N4L, active status in the addendum dated 5 February 2024 |
| TPS613221ADBVT | the same body on a 250 piece small reel, which is the string a pilot build orders before the main release |
| .B suffix row | the addendum repeats the reel string with a .B suffix, and the finish is read on the row rather than taken from the suffix |
| Three pin body | TPS61322 and TPS613223A come in a 2.90 mm by 1.30 mm three pin SOT-23, which is the smallest option in the family and carries the same die |
| Other voltages | TPS613222A is the 5 V member, TPS613226A the 3.6 V member, and TPS613223A the 2 V member, all in the same document |
| Preview rows | TPS613224A at 2.5 V and TPS613225A at 3 V are marked as preview in the comparison table, so they are not orderable as production parts |
| Marking | 1N4L on this string, and the marking changes with the voltage option rather than with the body |
Electrical parameters that decide the application
| Input voltage | 0.9 V to 5.5 V, which is what makes a single alkaline cell, a nickel metal hydride cell or a single lithium cell a usable input |
| Output voltage | 1.8 V to 5.5 V across the family in 0.1 V steps, set inside the package, and 3.3 V on this string |
| Output accuracy | 3 per cent over temperature, which is looser than a linear regulator and has to be allowed for in the load's own tolerance |
| Switch current limit | 0.75 A minimum, 1.20 A typical and 1.60 A maximum on this string, which is the number that caps the output current rather than the load rating |
| Quiescent current | 6.5 microamp into the output pin, which is the figure that decides the shelf life of a battery product |
| Efficiency | higher than 90 per cent at 10 mA from a 1.5 V input to a 2.2 V output, which is where a boost converter usually loses to a linear one |
| Control | hysteretic control with synchronous rectification, so there is no external compensation and the loop follows the inductor and the capacitor |
| Inductor and capacitors | the document gives a 2.2 microhenry inductor as the working value, with small ceramic capacitors on the input and the output |
| External diode | a Schottky in parallel with the internal rectifier raises the output current, and the 5 V member reaches 500 mA from a 3 V input with that diode fitted |
| Protection | thermal shutdown and the cycle by cycle switch current limit, with no separate overvoltage clamp on the output |
| Start up | the converter starts from the low input end of the range, which is what allows a board to run a cell down to 0.9 V rather than stopping at 1.8 V |
| Body | 5 pins in a 2.90 mm by 1.60 mm SOT-23, or 3 pins in a 2.90 mm by 1.30 mm body for the strings that use it |
Family variants and how they differ
| TPS61322 | 2.2 V output with a 0.75 A typical limit, the general purpose member of the family |
| TPS613221A | 3.3 V output with a 1.2 A typical limit, the string on this page |
| TPS613222A | 5 V output with a 1.8 A typical limit, the member for a 5 V sensor or a display bias, and the one that reaches 500 mA with an external Schottky |
| TPS613223A | 2 V output with a 0.75 A typical limit in the three pin body |
| TPS613226A | 3.6 V output with a 1.2 A typical limit, the member for a 3.6 V rail from a single cell |
| Voltage choice | the output cannot be changed on the board, so the voltage option is chosen at the order and a rail change is a string change |
Points to check before this part goes on a BOM
The output current is set by the switch limit, not by a rating. At 0.75 A minimum switch current, a 1.5 V input and a 3.3 V output, the usable output current is under 300 mA, and the efficiency at that point is what decides the battery life.
The output voltage cannot be adjusted. It is trimmed inside the package, so the 3.3 V string is a 3.3 V rail and a 3.0 V rail is a different string, which is why the family carries seven voltage options.
The quiescent current is quoted into the output pin. That is the number that matters on a boost converter, because the input current at no load is the output current divided by the conversion ratio, and 6.5 microamp at 3.3 V out becomes more at the cell.
An external Schottky is an option, not a requirement. Fitting one raises the output current, and it also removes the body diode drop from the conduction path, at the cost of a part and a placement.
There is no overvoltage clamp. If the load disconnects while the converter is regulating, the output rises until something breaks down, so a load that can be removed needs a clamp or a switch on the output.
Sizing the inductor for 3.3 V from one cell
The document works the family around a 2.2 microhenry inductor. At the low end of the input range the switch current for a given output is highest, so the inductor has to be chosen for the 0.9 V case rather than the 1.5 V case, and its saturation current has to sit above the 1.6 A maximum switch limit.
The input capacitor carries the pulsed current from the cell and the output capacitor carries the ripple from the rectifier. On a battery product the input capacitor is also the thing that keeps the cell impedance from modulating the loop, so a 10 microfarad ceramic close to the inductor is the usual starting point rather than the minimum in the table.
Where this order code fits
The part suits a meter, a remote control, a wireless sensor node or a portable medical device, where a single alkaline or nickel metal hydride cell has to produce a 3.3 V rail. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
How much current can it deliver at 3.3 V from one cell? Under 300 mA at the minimum switch current limit and a 1.5 V input. The exact figure depends on the inductor and the efficiency at that point, and the 1.2 A typical limit is not an output current rating.
Can the output be set to 3.0 V? Only by ordering the 3.0 V string, which the comparison table lists as a preview part. The output is fixed inside the package and there is no feedback pin.
Does it need an external diode? No. The rectifier is inside the package, and an external Schottky is added only when a higher output current is needed, as in the 5 V member reaching 500 mA from a 3 V input.
What happens if the load is removed? The output rises, because there is no overvoltage clamp. A load that can be disconnected needs a clamp or a switch, and a board that can see that condition should not rely on the converter alone.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.