Contact Us

TPS61299DRLR

Brand: Texas Instruments
Texas Instruments TPS61299DRLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61299DRLR — Power Management & Signal Chain | Superb Automation

TPS61299DRLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61299DRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61299DRLR the 1.2 A base member in a 1.6 mm SOT-563

The TPS61299DRLR is the base member of the TPS61299x family in a 6 pin SOT-563 body measuring 1.6 mm by 1.6 mm, with a 1.2 A input current limit, a 95 nanoamp quiescent current, an input range of 0.5 V to 5.5 V and an output range of 1.8 V to 5.5 V. It is the same die as the chip scale members, in a package that can be placed and inspected with ordinary surface mount equipment.

The SOT-563 version exists because the chip scale body at 1.2 mm by 0.8 mm is not practical on every line. The same electrical behaviour in a 1.6 mm square package costs board area and a little thermal performance, and it removes the need for a chip scale assembly process and an X ray inspection step. For a product that ships in thousands rather than millions, that trade usually goes to the SOT body.

The family behaviour carries over: start up from 0.7 V, operation down to 150 mV while the input remains above 0.7 V, snooze mode for microamp loads, normal mode for a load step, and thermal shutdown at 150 degrees.

Key parameters from the SLVSGS9G document

Input range0.5 V to 5.5 V, start up from 0.7 V on this member
Output1.8 V to 5.5 V, set by an external divider
Input current limit1.2 A average, the base step of the family ladder
Quiescent current95 nanoamp typical into the input pin, 4 nanoamp into the output pin
ShutdownTrue shutdown on this member, 60 nanoamp into the input pin with the enable low
Enable thresholdsLogic high above a 1.05 V input, 0.36 V logic low, which suits a directly driven pin
ProtectionThermal shutdown at 150 degrees with 20 degrees of hysteresis
Package6 pin SOT-563, 1.6 mm by 1.6 mm, DRL body, marking 61299, 4000 pieces on a large reel

Why the input current limit is the useful control

A boost converter that draws whatever the load needs will pull a coin cell or a small alkaline cell down to a voltage where the product resets. Limiting the average input current keeps the cell above that point, and the cost is that the output sags during a burst rather than the input collapsing. Between the two failure modes the sag is the one a product can ride through, because the output capacitor and the load's own tolerance absorb it.

On a lithium cell the same limit protects the cell from an over current event, and it also sets the maximum output power the converter can deliver. That is why the family spans 5 mA to 1.9 A: the limit is a circuit parameter, not a protection afterthought.

True shutdown on this member means the output is isolated from the input when the enable pin is low, so a product with a second supply holding the output does not leak back into the cell. The A suffix members do the opposite on purpose and pass the input through to the output.

Where this part fits

Coin cell and single cell products, battery backup rails, sensor nodes and any board that needs a nanoamp idle current in a package that can be assembled without chip scale tooling. Our desk keeps the family cross reference and the SOT against chip scale comparison, see power management cross reference and how to verify a drop in replacement.

What to check before a purchase order

The DRL body is 1.6 mm by 1.6 mm with 6 pins and 4000 pieces on a reel rather than the usual 3000, so a prototype order needs a cut tape. The marking is 61299, and the same body code appears on other 1 A and 2 A converters in the catalogue, so the marking rather than the body size is the check at goods inwards.

Confirm whether the board needs true shutdown or pass through. The A suffix member is a different order line and a different behaviour, and a board that relies on the output collapsing when the converter is disabled will not do that with the A part. See incoming inspection plan for the marking check and component lead time solutions when the chip scale version is short.

Questions that come up on this part

Is the SOT version electrically identical to the chip scale version, is the first question. The die and the electrical table are the same, and the difference is thermal: the SOT body has a higher junction to ambient resistance, so the current available at a given ambient is lower. The second question is whether the 1.2 A limit can be raised. It cannot, and a board that needs more has to move up the ladder to the 1.9 A member.

The third question is about the enable threshold at a 1.05 V input. Above that input the threshold is a normal logic level, and below it the threshold shifts, which allows the pin to be driven from the input rail through a resistor on a very low voltage source. A board that drives the pin from a processor running at 1.8 V is inside the normal case.