TPS612532AYFFR
Product Specifications
TPS612532AYFFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS612532AYFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS612532AYFFR a 3.5 MHz boost in a 9 ball chip scale package
The TPS612532AYFFR is a 9 ball chip scale part from the TPS6125x family of 3.5 MHz boost converters, which take 2.3 V to 5.5 V in and deliver up to 800 mA at a 4.5 V output from a 2.65 V input, 1000 mA at 5.0 V from 3.3 V, and 1500 mA as a peak for pulsed loads. The efficiency at 3.5 MHz is 93 per cent, the total DC voltage accuracy is 2 per cent, and the whole solution needs three surface mount parts: one inductor and two capacitors.
Quiescent current is 37 microamp in normal operation and 21 microamp in standby, where the converter holds its output biased at the input voltage level instead of regulating. That standby behaviour is unusual and useful: an audio amplifier or a load that can run from the battery directly stays powered while the boost sits idle, and the bias current drops.
At light load the part enters a power save mode with a low ripple pulse frequency scheme, and it can be configured to disconnect the load during shutdown so the battery is not drained through the converter. Shutdown current is under 5 microamp.
Key parameters from the SLVSAG8G document
| Input range | 2.3 V to 5.5 V, one lithium cell or a three cell alkaline pack |
| Output current | 800 mA at 4.5 V from 2.65 V, 1000 mA at 5.0 V from 3.3 V, 1500 mA peak for 20 ms pulses |
| Switching frequency | 3.5 MHz regulated, which is what allows a small chip inductor |
| Efficiency | 93 per cent at 3.5 MHz operation |
| Accuracy | 2 per cent total DC voltage accuracy |
| Quiescent current | 37 microamp normal, 21 microamp standby biased at the input level |
| Shutdown | Below 5 microamp with the load disconnected from the battery |
| Solution size | Three external parts, under 25 square millimetres total |
| Package | 9 ball NanoFree chip scale package, YFF body, 3000 pieces on a large reel, moisture level 1 |
Standby bias and what it is for
Standby mode holds the output at the input voltage through the high side switch rather than regulating it up. A load that can work from 3.0 V to 4.2 V directly, such as a class D audio amplifier or a motor driver, then runs from the battery with the boost contributing only 21 microamp of bias. When the load needs the full 5 V, the part leaves standby and regulates.
The catch is that the output is not protected in standby: it follows the input, including any sag, and the current is limited only by the switch and the load. A downstream circuit that needs a stable rail cannot use this mode and has to keep the converter regulating at 37 microamp.
This is why the datasheet quotes two quiescent currents instead of one, and why a standby budget has to say which mode the product is in. The difference between 21 and 37 microamp is small in absolute terms but it is the only number that changes between the two states.
Order code and the published rows
The catalogue string on this page is TPS612532AYFFR. The packaging addendum of the document lists TPS61253YFFR and TPS61253YFFT for the 9 ball YFF body, at 3000 and 250 pieces, and does not print a TPS612532AYFFR row. The suffix structure in the family is the device number plus a body code, so the extra characters in this string are not explained by the document.
That is stated here rather than smoothed over, because the difference matters at goods inwards. A distributor may fill this line with TPS61253YFFR, which is the same body and the same family, and the fixed output voltage still has to be confirmed, since the family covers several fixed outputs from 3.3 V to 5.2 V. The safe path is to confirm the output voltage and the reel label against the purchase order before the line starts.
Where this part fits
Portable audio, sensor nodes, small displays and any product where a 5 V rail has to fit in 25 square millimetres. Our desk keeps the boost cross reference and the second source notes for chip scale converters, see power management cross reference and pin to pin cross reference.
What to check before a purchase order
Confirm the fixed output voltage, not only the body. The family document covers six members with outputs from 3.3 V to 5.2 V in the same 9 ball body, and the addendum rows do not carry the voltage in the order string. A 5 V board built with a 4.5 V member regulates correctly and produces the wrong rail, which usually shows up as a marginal analog circuit rather than as an obvious fault.
Confirm the inductor for 3.5 MHz. A part specified at 2 MHz will have too much inductance and too much resistance at this frequency, and the efficiency will land well below the 93 per cent figure. See incoming inspection plan for the receipt check on a chip scale body, where the marking is a single character.
Questions that come up on this part
Can the part run without the boost when the battery is full, is the first question, and yes, that is the standby mode. The second is whether 1500 mA is a continuous rating. It is a peak for a 20 millisecond pulse at a 10 per cent duty cycle, which covers a camera flash or a transmit burst and not a steady load.
The third question is about the 2 per cent accuracy. It is a total DC figure and it assumes the internal divider, so there is no external tolerance to add. That is the main reason to use a fixed output part in this family rather than the adjustable one.