Contact Us

TPS61200DRCR

Brand: Texas Instruments
Texas Instruments TPS61200DRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61200DRCR — Power Management & Signal Chain | Superb Automation

TPS61200DRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61200DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61200DRCR: boost converter that starts from 0.5 V and delivers 1.35 A of inductor current

TPS61200DRCR is a synchronous boost converter built for single cell and energy harvesting inputs, starting at half a volt and regulating up to 5.5 V out in a VSON body of 10 pins. The TPS61200 runs from an input as low as 0.3 V and starts at 0.5 V, which is what makes it usable from a single alkaline cell, a solar cell or a fuel cell. It boosts to an adjustable output between 1.8 V and 5.5 V with a 500 mV feedback threshold, and the family includes fixed 3.3 V and 5 V members. The oscillator runs at 1650 kHz typical, the average inductor current limit is 1350 mA typical, and the switches are 150 mOhm main and 180 mOhm rectifying. Quiescent current is 50 uA with the output connected.

Order code and package

Order codeTPS61200DRCR
Input voltage0.3 V to 5.5 V
Start-up input voltage0.5 V minimum
Output voltageadjustable 1.8 V to 5.5 V
Feedback voltage495 mV to 505 mV
Oscillator frequency1250 kHz to 1650 kHz
Inductor current limit1200 mA minimum, 1350 mA typical, 1500 mA maximum
Main switch resistance150 mOhm
Rectifying switch resistance180 mOhm
Quiescent current50 uA typical, 70 uA maximum
Package10 pin VSON
Auxiliary output2.4 V to 5.5 V
DocumentSLVS577E, March 2007, revised December 2014

Electrical parameters that decide the application

Output current at 3.3 V300 mA with an input of 2.4 V or more
Output current at 5 V600 mA with an input of 3 V or more
Shutdown current0.5 uA typical on the input pin
Line regulation0.1 percent typical, 0.5 percent maximum
Load regulation0.1 percent typical, 0.5 percent maximum
Thermal resistance41.2 C per W for the 10 pin VSON
Junction range-40 C to 125 C
Ambient range-40 C to 85 C
Enable thresholdslow below 0.1 times the input voltage
Down modepasses the input to the output through the rectifier when the input exceeds the target
Auxiliary supplyfeeds the gate drive and can be taken from the output
ESD rating4 kV human body model

Points to check before this part goes on a BOM

Starting at half a volt is the feature that separates this part from ordinary boost converters. A single alkaline cell falls to 0.9 V under load and a coin cell to 2 V, and a converter that needs 1.8 V to start simply cannot use them. The part holds a separate start-up path until the output is high enough to supply its own gate drive through the auxiliary pin, and that handover is the behaviour to verify on a bench with a source that has real internal resistance.

The inductor current limit is 1.35 A typical, not an output current rating. At 3.3 V out from a 1.2 V input the input current is roughly three times the output current, so the available output current falls as the input falls. The published figures, 300 mA at 3.3 V from 2.4 V in and 600 mA at 5 V from 3 V in, are the numbers a battery life estimate should start from.

The auxiliary pin is what keeps the efficiency up at low input. Gate drive taken from a low input rail wastes charge, so the part can take it from the output or from a separate rail once the output is established. A board that ties the auxiliary pin to the input saves a connection but pays for it in efficiency at the bottom of the input range.

Down mode is easy to miss. When the input is above the target output, the part stops switching and the rectifier passes the input through, so the output follows the input minus a diode drop rather than holding at the set point. On a solar fed board that behaviour is wanted; on a board that expects a regulated 3.3 V from a 4.2 V battery it is not, and the output will sit above its nominal.

Quiescent current of 50 uA is quoted with the output connected and the part enabled but not switching. That figure, not the shutdown current, is what decides the shelf life of a harvesting node, and a board that leaves the converter enabled permanently should budget it against the average harvested power.

Thermal performance in a 10 pin VSON depends on the pad and the copper. At 300 mA out and 3.3 V out from a 2.4 V input the loss is around 0.3 W, which at 41.2 C per W is a 12 C rise, but at 600 mA and 5 V out the loss is closer to 0.6 W and the rise doubles. A board that runs at the top of the output range should check the pad area before the enclosure is fixed.

The 4 kV human body model rating is unusually high for a boost converter of this class, and it matters on a board where the input comes from a battery cable or a harvested source that can carry a discharge. Boards that connect the input to an external terminal should still add a transient suppressor, because the rating covers the device and not the wiring.

Where this order code fits

This order code belongs in equipment powered by a single cell, two or three alkaline cells, a lithium coin cell or a harvesting source, where the input collapses under load and the rail still has to hold 3.3 V or 5 V for a radio or a display. Wireless sensors, remote meters and portable medical strips are the usual sockets. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Can it really start from one alkaline cell? The start-up threshold is 0.5 V, so yes, provided the source can supply the inrush at that voltage. A cell with high internal resistance may need a storage capacitor at the input.

What is the maximum output current? It depends on the input. The inductor current limit is 1.35 A, so the output current falls as the input falls, and the published points are 300 mA at 3.3 V and 600 mA at 5 V.

Does the output stay regulated if the input rises above it? No. In down mode the rectifier passes the input through, so the output follows the input less a diode drop.

SUPERB supplies this order code with packing and date codes on the offer, and the Drone UAV Components page sets out how to plan a battery rail that must stay in production after the vendor moves on.