TPS61165DBVR
Product Specifications
TPS61165DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS61165DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS61165DBVR: white LED driver with a 1.2 A switch for backlights and indicator strings
TPS61165DBVR is a fixed frequency boost converter that drives a string of white LEDs from a constant current in a SOT-23 body of 6 pins. The feedback pin regulates 200 mV across the sense resistor, so the LED current is set by a resistor and not by the boost ratio. The switch is rated 1.2 A, the switching frequency is fixed at 1.2 MHz, and the input takes 3 V to 18 V while the output can rise to 38 V.
Order code and package
| TPS61165DBVR | 6-pin SOT-23 (DBV), 3000-piece large reel, marking DAK, -40 C to 85 C |
| TPS61165DBVT | 6-pin SOT-23 (DBV), 250-piece small reel, marking CCQ |
| TPS61165DBVRG4 | 6-pin SOT-23 (DBV), 3000-piece large reel, green row |
| WSON body | 6-pin WSON, 2.00 mm by 2.00 mm, for the footprint critical case |
| Moisture sensitivity, DBV rows | Level-1-260C-UNLIM, NIPDAU finish |
Electrical parameters that decide the application
| Input voltage range | 3 V to 18 V, absolute maximum 20 V |
| Output voltage ceiling | 38 V, limited by the open LED protection |
| Feedback regulation voltage | 196 mV minimum, 200 mV typical, 204 mV maximum |
| Feedback accuracy | 2 per cent |
| Switch current rating | 1.2 A |
| Switching frequency | 1.2 MHz, fixed |
| PWM dimming frequency | 5 kHz to 100 kHz on the CTRL pin |
| Undervoltage lockout | 2.2 V falling, 0.4 V hysteresis |
| Operating junction temperature | -40 C to 125 C |
Family variants and how they differ
| One wire digital dimming | a pulse train on CTRL sets the brightness and the part holds it |
| PWM dimming | a duty cycle on CTRL sets the brightness directly, 5 kHz to 100 kHz |
| Open LED protection | the part stops switching when the output runs away with no load |
| Series string | up to ten white LEDs in series from a 5 V rail, within the 38 V ceiling |
| Single inductor | one inductor and one diode, no charge pump and no second rail |
Points to check before this part goes on a BOM
The feedback pin regulates 200 mV, not the output voltage, which is the whole point of the part: the LED current stays the same as the string ages and as the forward voltages spread. A 10 ohm sense resistor therefore sets 20 mA and a 2 ohm resistor sets 100 mA, and the tolerance of that resistor is the tolerance of the brightness.
The 1.2 A switch sets the ceiling on the LED current. A string of six white LEDs at 3.3 V each needs about 20 V, and at 100 mA the switch carries more than 100 mA because the input current in a boost is higher than the output current by the voltage ratio, so the headroom shrinks as the string gets longer and the input rail gets lower.
Dimming works two ways on the same pin. A duty cycle between 5 kHz and 100 kHz is filtered into a DC level and gives analogue style brightness, while a one wire pulse train is decoded as a code. Both avoid bursting the LED current, which is why the part does not produce audible noise on the output capacitor at low brightness.
Open LED protection disables the switch when the output rises past the point where the string should be conducting. Without it, a broken string would let the boost run to the 38 V ceiling and hold the switch and the diode at their limits. A product that must report the fault has to detect the drop in the current through the sense resistor, because the part itself only stops switching.
The input range starts at 3 V, so the part runs from a single lithium cell or a 3.3 V rail, and it tolerates 18 V for the automotive and industrial case. The absolute maximum is 20 V, which leaves little margin on a 12 V rail with load dump, and a rail that can spike past 20 V needs a clamp ahead of the device.
Undervoltage lockout sits at 2.2 V falling with 0.4 V of hysteresis. On a lithium cell that discharges to 3.0 V this is comfortable, but a rail that sags during a motor start will drop the LEDs out and back on, and the visible flicker is the lockout rather than the dimming signal.
The 1.2 MHz frequency keeps the inductor small, in the 4.7 uH to 10 uH range for most backlights, and moves the switching energy above the band where it is hard to filter. It also raises the switching loss, so a board that runs at the full 1.2 A switch current in a small SOT-23 body has to watch the junction temperature rather than the ambient.
The sense resistor is in the current path and dissipates 200 mV times the LED current, which is 20 mW at 100 mA. That is small, but the tolerance of a 1 per cent resistor plus the 2 per cent feedback accuracy gives about 3 per cent brightness spread between units, which is invisible in a backlight and not acceptable in a calibrated indicator.
The DBV body is 2.90 mm by 1.60 mm with six pins, and two of them are the switch node and the input. The switch node carries the full inductor current in a small loop, so the input capacitor has to sit next to the pin and the return path has to stay under the body, otherwise the radiated field from that loop shows up in the emissions scan.
The tube and reel rows use different markings, DAK on the reel and CCQ on the small reel. A service centre that matches marking to order code will read the small reel as a different device, so the purchase order should name the full order code and the reel size rather than rely on the marking.
The CTRL pin is also the enable, so the dimming signal and the on off control share one line. A pulse train slower than the 5 kHz dimming floor is read as a series of enable and disable events rather than as a brightness level, and at a few hundred hertz that shows up as flicker at the panel refresh rate. A firmware that dims by lowering the pulse rate instead of the duty cycle will therefore produce exactly the artefact the part was chosen to avoid.
Where this order code fits
It drives the white LED string in a display backlight, an exit sign, an appliance panel or an indicator bar, where the input is a 3.3 V, 5 V or 12 V rail and the string needs a constant current rather than a constant voltage. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Obsolete Part Cross Reference Hub page.
Questions buyers ask
How many LEDs can one string hold? As many as fit under the 38 V ceiling. Ten white LEDs at 3.3 V need 33 V plus the 200 mV of sense voltage, which is inside the limit, but the switch current and the inductor have to be checked at that ratio.
Can the brightness be set by a microcontroller? Yes. A PWM signal between 5 kHz and 100 kHz on the CTRL pin sets the brightness, and a one wire pulse train sets a stored level. Both are accepted on the same pin, so a firmware change can move from one scheme to the other without a board change.
What happens if one LED fails open? The open LED protection stops the switch before the output reaches the absolute maximum. The string goes dark and the part stays off until the enable is cycled, which a host can detect by watching the current through the sense resistor.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.