Contact Us

TPS61161DRVR

Brand: Texas Instruments
Texas Instruments TPS61161DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61161DRVR — Power Management & Signal Chain | Superb Automation

TPS61161DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61161DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61161DRVR: 38 V white LED boost driver with one wire dimming

TPS61161DRVR is a boost converter that drives a series string of white LEDs in a WSON body of 6 pins. A 40 V switch inside a 2 mm by 2 mm body, a 200 mV feedback reference with 2 per cent accuracy, and a 38 V open LED clamp that keeps the output from running away when a string goes open. The part is set for 600 kHz and needs one inductor, one diode and one sense resistor.

Order code and package

TPS61161DRVRactive, production, WSON 6 pins, 3000 pieces on a large reel
TPS61161DRVRG4same die on a 250 piece small reel
MarkingBZR
Moisture levelLevel 2, 260 C, one year floor life
Temperatureminus 40 to 85 C ambient, not 125 C
Thermal padexposed pad on the underside, soldered to ground

Electrical parameters that decide the application

Input voltage2.7 V to 18 V
Switch rating40 V integrated FET
Open LED clamp38 V typical on the TPS61161, 26 V on the TPS61160
Feedback200 mV with 2 per cent accuracy
Switching frequency600 kHz fixed
Dimmingone wire digital through CTRL, or a PWM duty on the same pin
Current settingsense resistor from FB to ground, 200 mV divided by the LED current
Soft startbuilt in, no external capacitor
Audible noiseno burst mode, so no capacitor singing at dim levels
Inductor22 uH in the vendor application circuit

Family variants and how they differ

TPS61160same die with a 26 V open LED clamp for shorter strings
TPS6116138 V clamp, the member on this page
Dimming rangedigital mode covers the full range in steps, PWM mode follows the duty cycle
Open LED behaviourthe part disables instead of regulating at maximum duty
Output capacitor1 uF ceramic in the application circuit
DiodeSchottky rated above the string voltage, 40 V in the vendor circuit

Points to check before this part goes on a BOM

The two family members differ only in the open LED clamp, 26 V against 38 V. That is not a marketing split: a string of six white LEDs at 3.2 V needs 19.2 V and fits inside either clamp, while a string of nine needs 28.8 V and only survives on the 38 V part when one LED opens.

The ambient rating stops at 85 C. In a luminaire or a display backlight the board temperature is usually above that, and the 40 V switch and the diode both dissipate, so the thermal path from the exposed pad is part of the current budget rather than a detail.

LED current is set by 200 mV across the sense resistor. At 20 mA that is 10 Ohm, which is the value in the vendor circuit, and the 2 per cent accuracy belongs to the reference, not to the resistor. A 1 per cent resistor keeps the total near 3 per cent.

Dimming through the CTRL pin has two modes on one wire. A PWM signal sets the reference in proportion to the duty cycle, and the EasyScale protocol writes a digital code. The PWM path is the simpler one and keeps the converter out of burst mode, which is what avoids audible noise from the output capacitor.

Open LED protection disables the part rather than regulating at maximum duty. That is the safe behaviour for the switch and the wrong behaviour for a system that expects the rest of the panel to stay lit, so a multi string build needs a fault signal from elsewhere.

The 600 kHz frequency is fixed. Inductor choice therefore sets the ripple current directly, and a 22 uH part at 3 V in is already at the edge of continuous conduction at 20 mA, which is why the vendor circuit is drawn for a 3 V to 18 V input rather than a single cell.

A 40 V switch with a 38 V clamp leaves 2 V of margin. Any ring on the switch node from a long diode lead or a poor ground return eats into that, so the switch node loop has to be short and the output capacitor close to the diode cathode.

Strings longer than the clamp

Ten white LEDs at 3.2 V need 32 V, which sits inside the 38 V clamp with 6 V of headroom. Eleven needs 35.2 V and the margin is under 3 V, at which point the clamp fires on a cold string and the panel goes dark rather than dim.

Where a longer string is unavoidable, the honest options are a part with a higher switch rating or two shorter strings driven from two converters. Raising the input voltage does not help, because the clamp is on the output.

Dimming behaviour at the low end

PWM dimming scales the reference, so at 1 per cent duty the reference is 2 mV and the sense resistor drops 10 mV. Offset in the feedback amplifier then becomes a large fraction of the set point, and the light output at the bottom of the range is not linear with duty.

Digital dimming avoids that by writing a code rather than a voltage, at the cost of a protocol on the control pin. For a backlight that must be uniform at 1 per cent, the digital path is the one to use.

Both paths share one limitation. The converter has no way to turn the string off completely, because the switch is between the input and the output and the LED current path is closed through the sense resistor as soon as the enable pin is high. A display that must go fully dark needs a load switch in series, which is why a dimming scheme on this part always costs one extra device.

Heat inside a backlight

The converter sits next to the panel, and the panel is the heat source. With an 85 C ambient limit and a 2 mm by 2 mm body, the switch loss and the diode loss both have to leave through the exposed pad into a copper area that is often smaller than the pad itself needs.

The practical check is to run the board at the highest ambient the product allows with the string at full current and measure the pad temperature, not the air. A 20 C rise on the pad is normal, and a 40 C rise means the copper under the part is too small for the current the string is drawing.

Where this order code fits

The order code is used in display backlights, handheld instruments and automotive interior lighting where a small package and a wide input range matter more than absolute efficiency. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can it drive LEDs in parallel? No. The feedback is a single current sink, so parallel strings share current by matching rather than by control. Two strings need two converters or a current balance network.

What sets the maximum string voltage? The 38 V clamp on this member, not the 40 V switch rating. The clamp is the number that decides how many LEDs fit.

Is the sense resistor critical? It sets the current directly at 200 mV divided by its value, so a 1 per cent part holds the current to about 3 per cent with the reference error included.

Why is the ambient limit 85 C? The body is 2 mm by 2 mm with an exposed pad, and the switch and diode losses both land on that pad. Above 85 C ambient the junction margin is gone before the current limit is reached.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.