Contact Us

TPS61160DRVR

Brand: Texas Instruments
Texas Instruments TPS61160DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61160DRVR — Power Management & Signal Chain | Superb Automation

TPS61160DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61160DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61160DRVR: White LED boost driver with a 40 V switch and a 26 V open circuit clamp

TPS61160DRVR is a boost converter in the six pin DRV body that drives up to six white LEDs in series from a single cell, switching at a fixed 600 kHz and regulating the LED current against a 200 mV feedback reference in a WSON-6 body of 6 pins. The TPS61160 is a series LED driver with a 40 V rated integrated switch, a fixed 600 kHz switching frequency and a feedback reference of 200 mV. The LED current is set by a resistor from the feedback node to ground, so a 10 ohm resistor gives 20 mA, and the same pin can be driven by a one wire digital interface on the CTRL pin or by a PWM signal whose duty cycle scales the reference. Open circuit protection limits the output to 26 V typical, and the six pin body measures 2 mm by 2 mm with a thermal pad.

Order code and package

Order codeTPS61160DRVR
Switch voltage rating40 V
Topologyboost, series LEDs
Switching frequency600 kHz, fixed
Feedback reference200 mV
Open LED protection26 V typical
Dimmingone wire digital on CTRL, or PWM duty cycle
Packagesix pin WSON, DRV body, 2 mm by 2 mm

Electrical parameters that decide the application

LED current setting200 mV divided by the sense resistor
Typical sense resistor10 ohm for 20 mA
Typical inductor22 uH
Typical output capacitor1 uF
Typical compensation capacitor220 nF
Sibling order codeTPS61161, 38 V open LED protection for up to ten LEDs
Dimming behaviourcontinuous current regulation, no burst mode in the LED path
Thermal padexposed pad on the six pin body

Points to check before this part goes on a BOM

A 200 mV reference is what allows a small sense resistor, and a small sense resistor is what keeps the driver efficient. Ten ohms at 20 mA dissipates 4 mW, which is a quarter of a percent of a 1.5 W LED string. A driver with a 1.25 V reference would need 62 ohms for the same current and would burn 25 mW in the resistor, which on a battery product is the difference between a backlight that runs for hours and one that runs for less. The low reference also means the tolerance of the resistor is compared against a small voltage, so a 1 percent part is worth fitting.

Twenty six volts of open circuit protection sets the maximum number of LEDs, and the arithmetic is a LED forward voltage times the count plus the sense voltage. A white LED at 3.3 V takes six LEDs to 19.8 V, which leaves 6 V of headroom for tolerance and for the rise of the forward voltage at low temperature. A seventh LED at 23.1 V leaves less than 3 V, which is inside the tolerance of a batch of LEDs and outside it on a cold morning. The part that removes the question is the TPS61161, with 38 V of protection for up to ten LEDs.

Six hundred kilohertz is a compromise between inductor size and switching loss, and the typical application values show it: 22 uH and 1 uF are parts that fit under the display. Doubling the frequency to 1.2 MHz would halve the inductor and double the switching loss, which on a 20 mA load is a poor trade because the load current is small and the losses are dominated by the quiescent and the switching terms rather than by the conduction term. The frequency is fixed, so the inductor is the only board choice, and the datasheet's efficiency curves are given for the recommended value.

Continuous current regulation rather than burst dimming is the reason this part is quiet. A burst driver turns the converter on and off at the dimming rate, and every burst is a current step into the output capacitor, which is a mechanical force in a ceramic capacitor and an audible tone at the dimming frequency. This device regulates the current continuously and changes the reference instead, so the output capacitor sees a smooth current and the audible noise disappears. That property is worth more than a fraction of an efficiency point on a product that sits on a desk.

The one wire interface on the CTRL pin is a digital protocol rather than an analog level, so a firmware that toggles the pin for PWM dimming and a firmware that sends the digital codes are two different things on the same pin. A pulse train that looks like a dimming command to a person with a scope can be a valid digital word to the device, which is why the timing of the first pulse after enable is part of the protocol rather than an implementation detail. A board that drives the pin from a GPIO should treat the protocol as a driver with a state machine rather than as a PWM output.

Open circuit protection matters more than it looks on a display product, because the failure it prevents is a connector that comes loose. Without the clamp, a string that opens lets the boost converter drive its output to whatever the switch and the inductor can produce, which is above the rating of the switch and of the output capacitor. The 26 V clamp turns that into a controlled state: the converter stops switching and the output sits at a known voltage, so the part survives and the fault is reported by the display being dark.

The 2 mm by 2 mm body with a thermal pad carries the switch loss, and the loss is small because the current is 20 mA. What the pad is really for is the return of the switching loop, which has to reach the input capacitor and the ground plane without sharing a path with the feedback node. A 20 mA converter with a 200 mV reference has a feedback node that moves by 2 mV for a 10 percent change in current, so the noise floor of that node is the resolution of the dimming, and the routing is what protects it.

Where this order code fits

This order code belongs on display backlights in handheld instruments, GPS receivers, portable media players, appliance panels and small industrial displays, where the panel needs a string of LEDs at a constant current and the supply is a single lithium cell. It is also the part chosen where the dimming has to be free of audible noise, because the converter regulates the LED current continuously instead of bursting it, so the output capacitor does not sing at the dimming frequency. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

How many LEDs can one part drive? Six white LEDs in series at 3.3 V each is 19.8 V, which sits inside the 26 V open circuit protection with headroom for tolerance. A seventh LED is marginal and a tenth needs the TPS61161, which has 38 V of protection and is otherwise the same device.

How is the LED current set? By a resistor from the feedback pin to ground, with the pin regulated to 200 mV. A 10 ohm resistor gives 20 mA. The tolerance of the resistor appears directly in the current, and the 200 mV reference means the resistor dissipates only 4 mW at 20 mA.

Why is the dimming quiet? Because the converter regulates the LED current continuously and the dimming changes the reference instead of bursting the output. A burst driver steps the output current at the dimming rate, which excites the ceramic output capacitor mechanically. This part does not do that, so there is no tone at the dimming frequency.

What happens if an LED string opens? The output is clamped at 26 V typical, the converter stops switching and the part survives. Without the clamp the output would rise until something broke, which on a 40 V switch and a 16 V capacitor is the capacitor. The fault shows as a dark display rather than as a damaged board.

SUPERB holds and sources this driver line against the exact order code, with the reel, date code and country of origin stated on the offer. When a backlight circuit has to move to a second part, the Component Lead Time Solutions page sets out the checks that separate a working substitute from one that fails on the bench.