Contact Us

TPS61099DRVR

Brand: Texas Instruments
Texas Instruments TPS61099DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61099DRVR — Power Management & Signal Chain | Superb Automation

TPS61099DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61099DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61099DRVR: synchronous boost converter with nanoamp quiescent current for battery powered nodes

TPS61099DRVR is a synchronous boost converter that holds a rail alive from a single cell with sub microamp standby current in a WSON body of 6 pins. The input range starts at 0.7 V and stops at 5.5 V, the output is adjustable from 1.8 V to 5.5 V or fixed at 3.0 V, 3.3 V or 5.0 V, and the quiescent current into the input pin is 400 nA with a further 600 nA into the output pin. The switch peak current limit is 0.8 A minimum.

Order code and package

TPS61099x, six pin WSON (DRV)2.00 mm by 2.00 mm, 3000-piece large reel
TPS61099x, six ball WCSP (YFF)1.23 mm by 0.88 mm, 3000-piece large reel, marking 19J or 17X
Small reel rows250-piece small reel, YFF body, same marking family
Temperature range-40 C to 85 C
Assembly rowseach order code also has an .A or .B row for the second assembly site

Electrical parameters that decide the application

Input voltage range0.7 V to 5.5 V
Output voltage range, adjustable member1.8 V to 5.5 V
Fixed output options3.0 V, 3.3 V and 5.0 V members
Quiescent current into VIN400 nA typical, 0.6 uA maximum at 3.7 V
Quiescent current into VOUT600 nA typical
Shutdown current0.5 nA typical into the input pin with the device disabled
Switch peak current limit0.8 A minimum
Output accuracy in PWM modeplus or minus 3 per cent, 4.90 to 5.10 V on the 5 V member
UVLO on the input0.6 to 0.7 V rising
Efficiencyup to 75 per cent at 10 uA, up to 93 per cent between 10 mA and 300 mA

Members of the family and their output

TPS610992adjustable member, output set by an external divider, marking 19J
TPS610993fixed 3.0 V member, 2.94 V to 3.06 V in PWM mode
TPS610994fixed 3.3 V member, 3.23 V to 3.37 V in PWM mode
TPS610996fixed 5.0 V member, 4.90 V to 5.10 V in PWM mode
Down modethe output stays regulated when the input rises above it, no pass through jump
True shutdownthe load is disconnected from the input while disabled

Points to check before this part goes on a BOM

The numbers that matter on a coin cell or a lithium thionyl cell are the two quiescent currents, 400 nA into the input and 600 nA into the output, because they flow in parallel and add up to about one microamp. A 220 mAh cell therefore loses about 10 per cent of its capacity a year to the converter alone, which is the budget the rest of the node has to live inside.

Shutdown current is quoted at 0.5 nA typical into the input pin with the device disabled, and true shutdown means the output is disconnected from the input. That is the difference between a node that survives ten years and one that is flat in two, because a boost with a body diode path would leak through the load even with the switch off.

The input range starts at 0.7 V and the switch limit is 0.8 A minimum, so the part will start from a nearly flat cell, but the current available at 0.7 V in is a small fraction of the current at 3 V in. A board that has to deliver 100 mA at 3.3 V out needs an input above about 1.8 V, and the data sheet curves show where the ceiling falls.

Down mode keeps the output regulated when the input climbs above the target, instead of letting the output follow the input through a pass device. On a battery that starts at 3.6 V and discharges through 3.3 V, this is what keeps a 3.3 V rail at 3.3 V in the first hour instead of at 3.6 V, and it removes the step that would otherwise reset a load.

The fixed output members are trimmed in production, so the divider is inside the part and the accuracy is plus or minus 3 per cent in PWM mode. The adjustable member uses an external divider, and that divider's tolerance is added to the part's, so a 1 per cent pair is the sensible choice when the load has a tight window.

The switch peak current limit is 0.8 A minimum, not a typical figure, which means the part can deliver about 300 mA at 3.3 V out from 3 V in before the limit starts to fold the current back. Above that the output voltage falls, and the fall is graceful rather than a shutdown, which is usually what a sensor node wants.

Efficiency is quoted as 75 per cent at 10 uA and up to 93 per cent between 10 mA and 300 mA. A node that spends most of its life at 10 uA should be judged on the first number, and a node that wakes to transmit at 200 mA should be judged on the second, and the same part covers both because the switching scheme changes at light load.

The six ball WCSP body is 1.23 mm by 0.88 mm and needs a footprint with 0.4 mm pitch. That is a fine pitch part for a small board, and the inductor is then the tallest component on the node, so the mechanical envelope is set by the inductor rather than by the converter.

The undervoltage lockout wakes at 0.6 to 0.7 V rising, which is below the 0.9 V that a single alkaline cell reaches only at the end of its life. That means the part keeps working down to a cell voltage where most loads have already stopped, and the load, not the converter, becomes the thing that decides when the node dies.

Each order code also has an .A or .B assembly row with a different moisture level on some rows. For a board that is built in two plants, the reel label rather than the device marking is the only place the distinction appears, so the incoming inspection record should capture the label.

The inductor is the other half of the circuit: its value sets the peak current at a given load and the point at which the part leaves continuous conduction. A 2.2 uH part keeps the ripple high enough for the hysteretic loop to work at low current, while a 10 uH part lowers the peak current and the output ripple at the cost of a larger body. On a coin cell the inductor's series resistance matters as much as its inductance, because it sits in the path that carries the whole input current.

Where this order code fits

It holds a 1.8 V, 3.0 V or 3.3 V rail alive in a smart meter, a thermostat, a wearable or a wireless sensor node that runs from a single alkaline, a coin cell or a lithium thionyl cell and has to survive years on the same cell. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

How long will it run from one AA cell? The converter's own draw is about 1 uA from the two quiescent currents together, so the answer is set by the load duty cycle. A node that wakes for 20 ms every minute at 20 mA draws far more than the standby figure, and that wake current, not the quiescent current, decides the cell life.

Does it work when the battery is above the output voltage? Yes. Down mode keeps the output regulated instead of passing the input through, so a 3.3 V rail stays at 3.3 V while a fresh 3.6 V cell discharges through that level.

What sets the output current ceiling? The 0.8 A minimum switch limit and the input voltage. At 3 V in and 3.3 V out the part can pass about 300 mA before the limit folds back, and at 1.8 V in the same output can only supply a fraction of that.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Strategic Sourcing page sets out the checks that keep a substitute from failing on the bench.