Contact Us

TPS61092RSAR

Brand: Texas Instruments
Texas Instruments TPS61092RSAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61092RSAR — Power Management & Signal Chain | Superb Automation

TPS61092RSAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61092RSAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61092RSAR a 96 per cent synchronous boost fixed at 5 V

The TPS61092RSAR is a synchronous boost converter in a 16 pin QFN body measuring 4 mm by 4 mm, with a fixed 5.0 V output, a 1.8 V to 5.5 V input range and a 500 mA output current from a 1.8 V source. It is the fixed 5 V member of the TPS6109x family, alongside the adjustable TPS61090 and the 3.3 V TPS61091, and it shares the same die, the same pinout and the same 2.2 A typical switch current limit.

The converter replaces the usual external Schottky rectifier with a 55 milliohm PMOS switch, which is where the 96 per cent efficiency figure comes from at moderate load. Quiescent current into the battery pin is 10 to 25 microamp, shutdown current is 0.1 to 1 microamp, and the part disconnects the load from the input during shutdown with a dedicated circuit rather than relying on the backgate diode of the rectifier.

Control is a fixed frequency multiple feed-forward scheme, so the duty cycle responds to a change in input voltage before the error amplifier has moved. On a load that steps at the same rate as the input sag, that ordering matters more than the loop bandwidth figure.

Key parameters from the SLVS484C document

Input range1.8 V to 5.5 V, one lithium cell or two alkaline cells
OutputFixed 5.0 V on this member, adjustable up to 5.5 V on the TPS61090
Output current500 mA from a 1.8 V input, limited by the switch current
Switch current limit2.0 A minimum, 2.2 A typical and 2.5 A maximum at a 5 V output
On resistance55 milliohm rectifying switch, NMOS switch specified in the electrical table
Quiescent current10 to 25 microamp into the battery pin at no load, 0.1 to 1 microamp in shutdown
RegulationLine 0.6 per cent and load 0.6 per cent
Start upStart up current limit at 0.4 times the switch limit
Package16 pin QFN, 4 mm by 4 mm, RSA body, 3000 pieces on a large reel, moisture level 2

Load disconnect is a circuit, not a diode

In a conventional synchronous boost the backgate diode of the high side PMOS is forward biased when the converter is off, so the battery feeds the output through that diode and the product never really turns off. This family adds a circuit that breaks that path, which is why the shutdown current is measured in microamps rather than in the load current of the downstream circuit.

That behaviour has a practical consequence for a product that keeps its output rail alive from a second source, such as a USB connection. With the load disconnected, the boost does not fight the external supply and does not draw reverse current through its own rectifier. It also means the output capacitance discharges through the load rather than through the converter, so a fast restart sees a clean rail rather than a partially charged one.

The 0.4 times start up limit is the other half of the same idea. On power up the converter cannot deliver the full 2.2 A into an empty output bank, so it ramps with a lower limit until the output is close to regulation. A 22 microfarad output capacitor at 5 V therefore charges in a controlled way instead of pulling the battery down to its own lockout.

Where this part fits

Single cell products that need a 5 V rail for a sensor or a display, USB accessories, and any board where the load has to be truly disconnected in shutdown. Our desk keeps the boost cross reference and the second source notes for the TPS6109x family, see power management cross reference and pin to pin cross reference.

What to check before a purchase order

The RSA body is 16 pins on 4 mm by 4 mm and the part number carries the fixed output voltage, so the TPS61090, TPS61091 and TPS61092 are three different order lines in the same body. A bill that lists the family without the last digit will be filled with whichever member the distributor has, and a fixed 3.3 V part in place of the 5 V part is a silent failure on the bench.

The 2.5 A maximum of the switch limit is the number for the inductor. A 2.2 A inductor saturates before the limit acts on the worst case device, and a boost that saturates loses the current control loop entirely. Confirm the inductor saturation at the top of the window and at the highest operating temperature, where saturation falls by 10 to 20 per cent. See incoming inspection plan for the receipt check on a 4 mm QFN.

Questions that come up on this part

Why is the efficiency only 96 per cent at 3.6 V in, is a common question. The losses are the two switch resistances and the inductor resistance, and at 1.8 V in the current is nearly three times the output current, so the same milliohms cost three times as much. The 96 per cent figure belongs to the middle of the input range, not to the bottom.

The second question is whether the part can be paralleled for more current. It cannot, because the two converters will not share current without a droop mechanism, and the switch limits are set by the die rather than by an external resistor.