Contact Us

TPS61087DRCR

Brand: Texas Instruments
Texas Instruments TPS61087DRCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61087DRCR — Power Management & Signal Chain | Superb Automation

TPS61087DRCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61087DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61087DRCR: 2.5 V to 6 V input, 18.5 V step-up converter with a 3.2 A switch

TPS61087DRCR is a boost converter with an integrated 3.2 A, 130 milliohm switch for rails up to 18.5 V from a single cell or a 5 V supply in a VSON (DRC) body of 10 pins. It boosts 2.5 V to 6 V up to 18.5 V, switches at 650 kHz or 1.2 MHz, and carries 3.2 A through the internal switch, which is what allows a 12 V or 18 V output from a battery rail.

Order code and package

Ordering stringTPS61087DRCR, DRC package, 10-pin VSON, tape and reel
Package10-pin VSON and a thin VSON option, 3.00 mm by 3.00 mm
Ambient range-40 C to 85 C
Frequency650 kHz or 1.2 MHz, selected by the FREQ pin
CompensationExternal, on the COMP pin, so the loop can be tuned to the output capacitor
Soft startAdjustable by a capacitor on the SS pin

Electrical parameters that decide the application

Input range2.5 V to 6 V
Output voltageUp to 18.5 V
Switch current3.2 A rated, 130 milliohm on resistance
Switching frequency650 kHz or 1.2 MHz
Reference1.238 V nominal, 1.230 V to 1.246 V across the window, which sets the divider and the over voltage trip
ProtectionsUnder voltage lockout, thermal shutdown, cycle by cycle switch current limit
Output capacitorCeramic, with the ripple current rating set by the duty cycle and the load

Points to check before this part goes on a BOM

The switch current rating is not the output current. In a boost converter the inductor current is continuous while the output current arrives in pulses, so at 5 V in and 12 V out the input current is roughly 2.4 times the output current for an ideal converter, and 3.2 A of switch current becomes about 1.1 A of output at 85 percent efficiency. A quotation that treats the 3.2 A figure as a load rating will be wrong by more than a factor of two.

At a high step-up ratio the switch conducts for most of the period, so the conduction loss grows faster than the load. From 3.3 V to 18.5 V the duty is around 82 percent, which at a 1 A output means about 2.6 A of average switch current, and 130 milliohm then dissipates roughly 0.9 W in the package. The same part delivering 12 V from 5 V at 1 A dissipates about 0.35 W, so the thermal work has to be done for the worst ratio the product supports, not for the nominal one.

External compensation is a feature for a board that has an unusual output capacitor, and a burden for a board that does not. The data sheet gives a starting network for a ceramic output, and a board that copies that network onto a polymer capacitor will show a phase margin problem at light load. This is the one part in the family where the loop has to be checked on the bench rather than assumed.

The 650 kHz setting suits a 10 microhenry inductor and the 1.2 MHz setting a 4.7 microhenry part, and the difference in ripple current is what decides whether the inductor saturates at the top of the load range. At 1.2 MHz with 4.7 microhenry the ripple is about 0.9 A at 5 V in, so a 3 A saturation part has margin, while at 650 kHz with 10 microhenry the ripple is similar and the core loss is lower, which is the usual choice for a 12 V output at 1 A.

The 18.5 V ceiling is set by the switch and the internal node ratings, not by the feedback divider. A product that needs 24 V cannot get there with this part at any current, and the honest answer is a controller with an external FET. A 19 V output that sits just above the limit will work on the bench at light load and fail on the switch rating at full load, which is the kind of margin a quotation should not promise.

Soft start is a capacitor on the SS pin and it is the control on inrush. At 100 nF the ramp is tens of milliseconds, which keeps the battery from seeing a step and keeps a USB source from dropping out. A board that omits the capacitor still starts, because the pin has an internal default, and the inrush it produces is what shows up as a brownout on the 5 V rail during power-up rather than as a fault in the converter.

Where this order code fits

It is used for TFT LCD bias supplies, handheld instruments, GPS receivers, DSL modems, PCMCIA cards and any portable product that needs 12 V or 15 V from a single cell or a 5 V input. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop RF Supply page.

Questions buyers ask

Can it deliver 3.2 A at the output? No. 3.2 A is the switch current, and the output current is much lower because the inductor current is pulsed into the output, so the ratio depends on input voltage, output voltage and efficiency.

Does it need a Schottky diode? The synchronous switch handles the rectification inside the part for the standard topology, and the data sheet typical application shows the external parts the reference board uses.

What is the highest output voltage? 18.5 V, set by the device ratings. A higher rail needs a controller with external FETs rated for the voltage.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.