TPS61029QDPNRQ1
Product Specifications
TPS61029QDPNRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS61029QDPNRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS61029QDPNRQ1 a 1.8 A switch boost that starts from 0.9 V
The TPS61029QDPNRQ1 is a synchronous boost converter in a 10 pin VSON body, qualified for automotive applications, that takes 0.9 V to 6.5 V in and produces an adjustable 1.8 V to 5.5 V out. It is the adjustable member of the TPS6102x-Q1 family, with a switch current limit of 1.5 A minimum and 2.1 A maximum around a 1.8 A typical, and a total accuracy of 3 per cent including line and load regulation.
The input range is the interesting part. A single alkaline cell starts at 1.5 V and ends near 0.9 V, and this converter holds regulation down to that floor, which is what allows a product to use the last of the cell rather than cutting off at 1.1 V. From a 3.3 V rail it delivers 5 V at up to 500 mA, and from a single cell it delivers 200 mA at 3.3 V.
The converter is synchronous, with a 260 milliohm NMOS switch and a 290 milliohm PMOS rectifier measured at a 3.3 V output, and it includes an anti-ringing circuit that damps the switch node when the inductor current reaches zero. That damping is what keeps the radiated emissions of a boost converter from turning into a problem in a small enclosure.
Key parameters from the SLVSA31A document
| Input range | 0.9 V to 6.5 V, with undervoltage lockout at 0.8 V on a falling input |
| Output | Adjustable 1.8 V to 5.5 V against a 500 mV reference |
| Switch current limit | 1.5 A minimum, 1.8 A typical and 2.1 A maximum at a 3.3 V output |
| On resistance | 260 milliohm NMOS switch and 290 milliohm PMOS rectifier at a 3.3 V output |
| Quiescent current | 25 microamp typical, 1 to 3 microamp in shutdown |
| Accuracy | 3 per cent total including line and load regulation, line and load each 0.6 per cent |
| Efficiency | 96 per cent at the nominal operating point |
| Package | 10 pin VSON, DPN body, 3000 pieces on a large reel, moisture level 3 with a 168 hour floor life |
| Qualification | Automotive, minus 40 to plus 125 degrees, marking 61029Q |
What a 1.8 A switch limit means at the output
The switch current limit is not an output current rating. In a boost converter the average input current equals the output current multiplied by the ratio of output to input voltage divided by the efficiency, so at 0.9 V in and 3.3 V out the input current is nearly four times the output current. With a 1.5 A minimum limit, the usable output at that operating point is around 300 mA before the limit is reached, and the 200 mA figure in the description is the conservative number that leaves room for ripple.
At a 3.3 V input and a 5 V output the ratio is 1.5, so the same limit supports about 800 mA of output in theory and 500 mA in the tables with margin. An engineer who reads the 1.8 A as an output rating will build a board that current limits at half the expected load, which is the most common mistake with this class of part.
The 500 mV reference also sets the divider choice. With a low reference the feedback divider carries more current for the same output, and on a 25 microamp quiescent part that current can dominate the idle draw. A 1 megaohm divider on a 5 V output draws 4.5 microamp, which is acceptable; a 100 kilohm divider draws 45 microamp and doubles the idle current.
Where this part fits
Single cell and dual cell battery products, automotive sensor nodes on a 5 V rail, backup supplies and any board that has to hold regulation down to 0.9 V. Our desk keeps the boost converter cross reference and the automotive second source notes, see power management cross reference and pin to pin cross reference.
What to check before a purchase order
The DPN body carries moisture level 3 with a 168 hour floor life, which is the tightest classification in this whole batch of parts. A reel that has been open for a week has to be baked before reflow, and a production line that treats it like a level 1 part will see delamination. The DRC body version of the same die, TPS61029QDRCRQ1, is also listed at 3000 pieces, so the two bodies are separate order lines.
Confirm the inductor against the 2.1 A top of the switch limit rather than the 1.8 A typical. A boost inductor that saturates at 2 A will let the current run away before the limit acts, and the input source then sets the current. Confirm the output capacitor against the load step: a boost converter has a right half plane zero, and the loop is slower than a buck, so a large step needs more output capacitance than the same load on a buck. See incoming inspection plan for the moisture sensitive handling check.
Questions that come up on this part
Can it run from a single 1.5 V cell at 200 mA output, is the first question. It can, at a 3.3 V output, and the efficiency at that point is around 80 per cent rather than the 96 per cent headline, because the input current is high and the resistances dominate. The second question is whether the anti-ringing switch can be disabled. It cannot, and that is deliberate, because the ringing it damps would otherwise appear as emissions.
The third question is about the 3 per cent total accuracy. It includes line and load regulation but not the divider tolerance, so a 1 per cent divider on top gives about 4 per cent at the output. A rail that has to hold 5 per cent over temperature needs a divider of 0.5 per cent or better.