TPS60403DBVR
Product Specifications
TPS60403DBVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS60403DBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS60403DBVR the 250 kHz member of the 60 mA inverting pump family
The TPS60403DBVR inverts a 1.6 V to 5.5 V input to minus that voltage and delivers up to 60 mA, using only three 1 microfarad ceramic capacitors. It is the highest frequency member of the TPS6040x family at a fixed 250 kHz, which is what allows the smallest capacitors in the group: the 20 kHz member needs 10 microfarad, the 50 kHz member needs 3.3 microfarad, and this one needs 1 microfarad.
Quiescent current is 65 microamp typical, and the marking is PFNI in the 5 pin SOT-23 DBV body. The commercial family covers minus 40 to plus 125 degrees on the plain reel row, while the G4 row of the same string is specified to 85 degrees, so the two rows are not interchangeable in a hot application even though the part number looks the same.
The part is aimed at the small negative rail that a signal chain needs: the bias for a rail to rail output stage, the negative supply of a multiplexer, or the contrast voltage of a small display. It is not a power converter, and treating it as one is the most common mistake made with this family.
Key parameters from the SLVS324C document
| Input range | 1.6 V to 5.5 V, wider than the automotive version at both ends |
| Output | Minus the input, unregulated, 60 mA maximum |
| Switching frequency | Fixed 250 kHz, the fastest member of the family |
| Flying capacitor | 1 microfarad, with the input and output capacitors at the same value |
| Quiescent current | 65 microamp typical, 425 to 700 microamp in the worst case row of the electrical table |
| Output ripple | 20 millivolt peak to peak at 5 mA with 3.3 microfarad capacitors on the TPS60402 rows |
| Package | 5 pin SOT-23, DBV body, marking PFNI, 3000 pieces on a large reel |
| Temperature | Minus 40 to plus 125 degrees on the plain row, 85 degrees on the G4 row |
The frequency choice is a capacitor choice
The four members of this family differ only in frequency and in the flying capacitor they are specified with, and that is a useful way to pick one. If the board has space for a 10 microfarad ceramic and the board is sensitive to radiated emissions, the 20 kHz member is the quietest. If the board is dense and the negative rail feeds a low current load, the 250 kHz member with 1 microfarad parts is the smallest solution, at the price of a switching component at 250 kHz that has to be kept away from sensitive traces.
The output impedance scales with the inverse of frequency and capacitance, so the 250 kHz member with 1 microfarad and the 50 kHz member with 3.3 microfarad land in a similar place. What changes is the ripple frequency and the size of the capacitors, not the fundamental capability.
The quiescent current row in the electrical table carries two numbers, 65 microamp typical and 425 to 700 microamp as a worst case, and the difference matters on a battery product. The typical figure is what a bench measurement shows at room temperature; the maximum is what the datasheet guarantees over the full range, and a standby budget has to be built on the second number.
Where this part fits
Signal chain negative rails, display bias, multiplexer supplies and any board that needs a small negative voltage from a positive rail. Our desk keeps the charge pump cross reference and the substitution notes for the four family members, see power management cross reference and how to verify a drop in replacement.
What to check before a purchase order
The G4 row of the same part number is specified to 85 degrees rather than 125, and the two rows carry the same 3000 piece quantity and the same marking. On a board that runs above 85 degrees ambient the G4 part is out of specification even though it will work on a bench. The reel label and the order line have to name the row, and a distributor substitution between them is not acceptable.
Confirm the three capacitors as a set. A 1 microfarad flying capacitor with a 10 microfarad output capacitor will produce a larger ripple than the tables show, because the charge transferred per cycle is set by the smaller part. On a 250 kHz part the capacitors are small enough that a 0402 X7R is adequate, and the dielectric temperature coefficient matters more than the value at 25 degrees. See incoming inspection plan for the marking check on a five pin body.
Questions that come up on this part
Is the TPS60403 a drop in for the TPS60402, is the first question. It is pin compatible and it will work, but the flying capacitor value differs, so a board built for a 3.3 microfarad part is over specified rather than wrong, and a board built for a 1 microfarad part used with the 50 kHz device will droop more at load. The second question is whether the output can be used as a reference. It cannot, because the output tracks the input and has no regulation loop.
The third question is about noise. At 250 kHz the switching component is above the audio band and below most radio bands, but its harmonics reach into the AM band. A small series resistor in the flying capacitor path, or a filter on the output, is usually enough to keep it out of a receiver front end.