Contact Us

TPS60402QDBVRQ1

Brand: Texas Instruments
Texas Instruments TPS60402QDBVRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS60402QDBVRQ1 — Power Management & Signal Chain | Superb Automation

TPS60402QDBVRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS60402QDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS60402QDBVRQ1 a 60 mA inverting charge pump for automotive rails

The TPS60402QDBVRQ1 generates a negative output equal to minus the input from a 1.8 V to 5.25 V supply, delivers up to 60 mA, and needs only three external capacitors. It is the automotive qualified member of the TPS6040x family, with AEC-Q100 Grade 1 qualification over minus 40 to plus 125 degrees, HBM classification level 2 and CDM level C6, in a 5 pin SOT-23.

This specific member runs at a fixed 50 kHz and uses a 3.3 microfarad flying capacitor, which places it in the middle of the family between the 20 kHz and 250 kHz versions. The lower frequency reduces switching losses and radiated energy, and the larger flying capacitor keeps the output impedance low enough to hold 60 mA. The output is unregulated and tracks minus the input, so the load has to tolerate a rail that moves with the supply.

An integrated active Schottky diode allows start up into a load, which matters on a board where the negative rail feeds an operational amplifier that is already biased from the positive rail at power up. Without that diode the negative rail would be pulled up by the load and the pump would not start.

Key parameters from the SGLS246B document

Input range1.8 V to 5.25 V, which is narrower at the top than the commercial family
OutputMinus the input, unregulated, up to 60 mA
Switching frequencyFixed 50 kHz
Flying capacitor3.3 microfarad, and the input and output capacitors must match it
External partsThree capacitors, no inductor and no diode
Quiescent current100 microamp typical for the family
QualificationAEC-Q100 Grade 1, minus 40 to plus 125 degrees, HBM level 2, CDM level C6
Package5 pin SOT-23, DBV body, 3000 pieces on a large reel, moisture level 1

Why an unregulated negative rail is often the right answer

A negative rail that tracks the positive supply is exactly what an operational amplifier needs when its output swing is referenced to the same supply. The quiescent current of the amplifier sets the load, a few milliamps in most signal chains, and the 60 mA capability is there for the transient when the amplifier drives a cable. A regulated negative rail would add a second control loop and a second failure mode for no benefit in that application.

The output impedance of the pump is set by the flying capacitor and the frequency. At 50 kHz with 3.3 microfarad, the equivalent resistance is low enough that the output droops by roughly a volt at 60 mA, which is the number to check against the amplifier headroom. At 10 mA the droop is a few hundred millivolts, which is the operating point that matters.

The automotive qualification is the reason to pay for this part rather than the commercial version. Grade 1 covers the full minus 40 to plus 125 degree ambient range, and the ESD classifications are stated per device rather than as a family claim.

Where this part fits

Automotive sensor modules, instrument clusters, audio amplifiers that need a negative rail, and any board that has to run from a 5 V or 3.3 V rail and produce a small negative supply. Our desk keeps the cross reference and the second source notes for charge pumps, see power management cross reference and pin to pin cross reference.

What to check before a purchase order

The order code is TPS60402QDBVRQ1, which decodes as the 3.3 microfarad flying capacitor, 50 kHz, SOT-23, reel, automotive grade. The addendum lists the plain row and two suffixed rows with the same 3000 piece quantity, so the reel label has to be read rather than the carton. The 5.25 V top of the input range is lower than the 5.5 V of the commercial family, which matters on a 5 V rail with a transient.

The three capacitors have to match. A board that fits a 1 microfarad flying capacitor because that is what the commercial sibling uses will run, but the output impedance rises and the droop at 60 mA roughly triples. Confirm the capacitor dielectric against the bias voltage, since a small X5R part loses most of its capacitance at 5 V. See incoming inspection plan for the marking check on a five pin body.

Questions that come up on this part

Can the output be regulated, is the first question, and it cannot without an external linear regulator. The second is whether the part can supply more than 60 mA. It cannot, and a load that needs more should look at a switched inductor converter with a coupled winding or a dedicated inverting regulator.

The third question is about the start up into a prebiased negative rail. The integrated active Schottky is what makes that work, and it is also why the part can be used on a board where the negative rail is held by another source during a partial power down.