Contact Us

TPS566247DRLR

Brand: Texas Instruments
Texas Instruments TPS566247DRLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS566247DRLR — Power Management & Signal Chain | Superb Automation

TPS566247DRLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS566247DRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS566247DRLR 6 A in a 1.6 mm SOT-563 with forced continuous conduction

The TPS566247DRLR is a 3 V to 16 V, 6 A synchronous buck in a 6 pin SOT-563 body measuring 1.6 mm by 1.6 mm, with a 27.7 milliohm high side and a 14.8 milliohm low side FET. It is the forced continuous member of the TPS56624x pair: the other member, the TPS566242, drops into a skip mode at light load and lets the frequency fall, while this one keeps a fixed 600 kHz and a fixed ripple at any load.

Both parts share the body, the pinout, the 0.6 V reference and the 3 V to 16 V input range, so the choice between them is a behaviour decision rather than a board decision. Reference accuracy is 1 per cent at 25 degrees and 1.5 per cent across the minus 40 to 125 degree range, the internal soft start is 1.39 ms, and the quiescent current is 120 microamp.

The package is the headline. A 6 A converter in 1.6 mm square is smaller than most 1 A parts were a decade ago, and the price of that density is thermal: the copper under the part is the only heat path, and the numbers have to be checked against the real board rather than against the front page.

Key parameters from the SLUSEN0A document

Input range3 V to 16 V, waking at 2.75 V to 3 V and shutting down at 2.6 V to 2.72 V
Output current6 A continuous from a 27.7 milliohm high side and a 14.8 milliohm low side FET
Output voltage0.6 V to 7 V, 594 mV to 606 mV at 25 degrees, 1.5 per cent over temperature
Switching frequency600 kHz fixed at 25 degrees with a 3.3 V output
Current limitValley threshold 6 A minimum and 7.4 A maximum, negative limit 2 A to 3.4 A
Quiescent current120 microamp no load and not switching, shutdown 0.4 microamp typical
Timing limitsMinimum on time 50 ns, minimum off time 100 ns
Soft start1.39 ms internal
Package6 pin SOT-563, 1.6 mm by 1.6 mm, DRL body, 4000 pieces on a large reel, moisture level 1

Six amps in 2.6 square millimetres

The conduction loss at full load is set by the two resistances and the duty cycle. From 12 V to 1.0 V the low side conducts for about 92 per cent of the period and dissipates roughly half a watt at 6 A, while the high side adds a little over 0.08 W. Half a watt in a 1.6 mm by 1.6 mm body is a junction rise that depends almost entirely on the copper attached to the pad, so the usual rule applies: the part is a 2 A to 3 A device on a two layer board with a short stub, and a 6 A device only when the pad is stitched into a plane.

That is not a criticism of the part, it is what the arithmetic says about any 6 A converter in this footprint. The honest way to use it is either at a lower current with a good thermal path, or at 6 A with a deliberate thermal check and a junction temperature measured at the worst case ambient rather than assumed.

The forced continuous behaviour helps here in one unexpected way: the ripple amplitude is fixed, so the RMS current in the output capacitor and in the inductor is predictable at every load. A skip mode part makes the RMS current at light load depend on the skip pattern, which makes the capacitor self heating harder to bound.

Where this part fits

Dense point of load rails, modules with a height limit, and any board where the light load ripple must not change. Our desk keeps the pair comparison, since the TPS566242 and the TPS566247 are the same board with different behaviour, see power management cross reference and pin to pin cross reference.

What to check before a purchase order

The DRL body is 1.6 mm by 1.6 mm with 6 pins, and the same body code appears on 1 A and 2 A parts from other families, so a reel label check is not optional. The order code ends in 247 for this part and 242 for the skip mode sibling, and the difference is one digit on the label. The reel is 4000 pieces rather than the usual 3000, which changes the quantity on a prototype order.

The second check is the input range against a 3.3 V rail. The wake threshold tops out at 3 V and the shutdown at 2.72 V, so a 3.3 V rail has about 300 mV of margin before the part stops. A 5 V rail is comfortable; a 3.3 V rail needs an input capacitor sized for the actual load step, not for the datasheet typical. See incoming inspection plan for the marking check on a six pin body.

Questions that come up on this part

Is the TPS566242 a drop in replacement, is the first question. Mechanically yes, both are the DRL body with the same pinout, and the difference is the light load behaviour, so a board can use either and the decision can be made late. The second question is whether 6 A is real in this body. It is a junction rating, and the ambient current depends on the copper, so the answer is a measurement rather than a number.

The third question is about the 120 microamp quiescent current. It is measured with the converter not switching, which is not a state the part reaches under load. On a standby budget the number that matters is the shutdown current, 0.4 microamp typical, with the enable pin pulled low.