Contact Us

TPS566238PRQFR

Brand: Texas Instruments
Texas Instruments TPS566238PRQFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS566238PRQFR — Power Management & Signal Chain | Superb Automation

TPS566238PRQFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS566238PRQFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS566238PRQFR 6 A buck that runs from a 3 V rail with 98 per cent duty

The TPS566238PRQFR is a 3 V to 18 V, 6 A synchronous buck in a 9 pin VQFN-HR body measuring 1.5 mm by 2.0 mm. The low end of the input range is the point of this device: 3 V minimum means it runs from a 3.3 V rail with margin, which most 6 A converters in this size class cannot do because their lockout sits above 4 V. The high side FET is 20.8 milliohm and the low side 10.6 milliohm, both measured at 25 degrees with a 5 V input.

Control is D-CAP3 at 600 kHz with a 0.6 V reference trimmed to 1 per cent, and the maximum duty cycle is 98 per cent, so the part can hold regulation when the input falls close to the output. That combination covers the dropout case that matters on a battery backed 3.3 V rail, where the input sags to 3.4 V and the output still has to deliver 3.3 V at load.

The P suffix on this order code is not cosmetic. The P version exposes the soft start charge current, so an external capacitor lengthens the ramp, and its undervoltage hiccup enable delay is 19 ms rather than the shorter default. On a board with a large output bank or a hot plug event, that difference decides whether a transient becomes a hiccup or a shutdown.

Key parameters from the SLUSDQ7B document

Input range3 V to 18 V, UVLO shutting down at 2.44 V to 2.64 V
Output current6 A continuous from a 20.8 milliohm high side and a 10.6 milliohm low side FET
Output voltage0.6 V to 7 V, 594 mV to 606 mV feedback window at 25 degrees
Maximum duty cycle98 per cent, which is what lets the part follow a collapsing input
Switching frequency600 kHz at 25 degrees with a 1.0 V output
Quiescent current25 to 75 microamp no load, 3.2 to 5 microamp shutdown
Soft start0.93 ms to 2.9 ms internal, charge current 5 to 8.5 microamp on the P version for an external capacitor
Power goodLower window 85 to 90 per cent, upper window 105 to 115 per cent of the feedback voltage
Package9 pin VQFN-HR, 1.5 mm by 2.0 mm, RQF body, 3000 pieces on a large reel

98 per cent duty and what it does to the loop

At 98 per cent duty the high side FET is on for almost the whole period and the low side is on for a sliver. Below the point where the low side can no longer refresh the bootstrap capacitor, the part has to skip a cycle to recharge it, and that appears at the output as a small step rather than as a clean DC level. The document states the 98 per cent figure as a maximum, and the practical consequence is a dropout characteristic rather than a hard limit: the output follows the input minus a small offset, and the loop takes longer to recover when the input comes back.

That behaviour is acceptable on a rail that only sees a sag during a hot plug or a battery end of discharge, and it is not acceptable where the output has to stay in regulation through a deep sag. For the second case the answer is a boost stage or a wider input part, not a different setting on this one.

The output discharge resistor is 114 ohm with the enable pin low, which is enough to bring a 100 microfarad rail down in a few milliseconds so that a re enable sequence sees a clean start. That matters on a board where the same rail powers a processor that is reset and restarted without a full power cycle.

Where this part fits

3.3 V input boards, battery backed industrial controllers, point of load rails that must survive a supply sag, and any 6 A rail in a 1.5 mm by 2.0 mm space. Our desk keeps the cross reference and the second source notes for the small body 6 A class, see power management cross reference and one stop BOM sourcing.

What to check before a purchase order

The order code carries a P between the part number and the body code, and the addendum lists TPS566238PRQFR and TPS566238RQFR as separate rows with the same 3000 piece quantity and the same body. The two differ in the soft start and the hiccup delay, so a bill that drops the P is a different part in behaviour even though the marking may look the same. Confirm the row on the reel label.

Second, check the input capacitor against the 3 V floor. A rail that sits at 3.3 V nominal has very little margin above the 2.44 V to 2.64 V lockout, and an input ceramic that loses capacitance under bias will let the rail ring below the lockout during a load step. See incoming inspection plan for the receipt check on a 9 pin body and component lead time solutions when the P row is short.

Questions that come up on this part

Can the part run at 2.5 V input, is the first question, and the answer is no, the lockout tops out at 2.64 V and the recommended range starts at 3 V. The second is whether the 19 ms hiccup delay is a fixed number. It is a delay relative to the undervoltage detection, so the total time to restart is that delay plus the soft start ramp, which is why a long ramp capacitor stretches the recovery.

The third question is about the 1.5 mm by 2.0 mm body at 6 A. The pad is small and the current is not, so the thermal path has to go through vias into an inner plane. A two layer board with no plane will run the part into thermal shutdown well before 6 A.