TPS566235RJNR
Product Specifications
TPS566235RJNR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS566235RJNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS566235RJNR 6 A from 18 V in a 3 mm by 2 mm QFN with a mode pin
The TPS566235RJNR is a 4.5 V to 18 V, 6 A synchronous buck in a 13 pin VQFN-HR body measuring 3 mm by 2 mm. It integrates a 25 milliohm high side and a 12 milliohm low side FET, runs at 600 kHz, and uses D-CAP3 control with no external compensation. The output range is 0.6 V to 7 V against a 600 mV reference trimmed to 1 per cent at room temperature, and the internal soft start is 1 ms.
The feature that makes this part interesting is the MODE pin. It selects between three light load behaviours: Eco-mode pulse skipping, an Out-of-Audio mode that keeps the switching frequency above 25 kHz, and forced continuous conduction. One body, one bill of materials, three different behaviours that are chosen by a pin strap rather than by a different order code.
Quiescent current is 108 microamp, which is low for a 6 A converter and is the number that matters on a board that has to idle. The part also starts into a prebiased output and supports seamless transition between continuous and discontinuous conduction, so a load step from 10 mA to 6 A does not produce a glitch at the mode boundary.
Key parameters from the SLVSEW1B document
| Input range | 4.5 V to 18 V, UVLO shutting down at 3.6 V to 3.7 V |
| Output current | 6 A continuous from a 25 milliohm high side and a 12 milliohm low side FET |
| Output voltage | 0.6 V to 7 V, 600 mV reference at 1 per cent at room temperature |
| Switching frequency | 600 kHz, with the Out-of-Audio mode holding the frequency above 25 kHz at light load |
| Quiescent current | 108 microamp with the enable pin high and the converter not switching |
| Internal rail | VCC 4.75 V to 4.92 V when the input is above 5 V, current limited at 20 mA |
| Soft start | 1 ms internal, no external capacitor |
| Enable thresholds | 1.22 V to 1.42 V rising and 1.04 V to 1.20 V falling |
| Package | 13 pin VQFN-HR, 3 mm by 2 mm, RJN body, moisture level 2 with a one year floor life |
Why Out-of-Audio matters on a 6 A rail
A pulse skipping converter at a few milliamps drops its switching rate into the audible band, and a ceramic capacitor with a high dielectric constant will sing at that rate. On a board that sits on a desk or in a handset, that is a customer complaint rather than a measurement. The Out-of-Audio setting keeps the switch node above 25 kHz at light load, which moves the excitation above what anyone can hear, at the cost of a slightly lower light load efficiency than the true skip mode.
Forced continuous conduction is the third option and the right one when the rail feeds something that cannot tolerate a changing ripple. It costs the most at light load and gives the most predictable waveform. Having all three in one part means the choice can be deferred until the acoustic and emissions measurements are done, and the strap can be changed on the same board without a new part number.
The 108 microamp quiescent current belongs to the skip mode with the output in regulation. In forced continuous conduction the figure is the switching loss of the two FETs at 600 kHz, which is several milliamps. A standby budget has to say which mode it is measured in, or the number in the document will not match the board.
Where this part fits
18 V input industrial boards, 12 V bus telecom line cards, set top boxes and any 6 A rail where the light load behaviour has to be selectable. Our desk keeps the family cross reference and the second source notes for the 6 A class, see power management cross reference and how to verify a drop in replacement.
What to check before a purchase order
The RJN body is 3 mm by 2 mm with 13 pins, and moisture level 2 with a one year floor life means the reel has to be dry stored or baked before use, which is different from the level 1 parts that dominate the small buck class. The RJNR row is 3000 pieces on a large reel, RJNT is 250 on a small reel, and the RJNTG4 row of the same string carries a different packing note, so the order line has to name the exact row.
The MODE pin must not be left floating. A board that straps it through a 10 kilohm resistor to either rail is safe; a board that relies on an internal default is not, because the pin decides between three behaviours that all look correct on a bench at full load. Confirm the strap against the acoustic and standby requirements before the first build, not after. See incoming inspection plan for how we check a 13 pin quad flat no lead body.
Questions that come up on this part
Does the mode pin change the current limit, is a common question, and it does not. The three modes change the light load switching pattern, not the protection thresholds, so the inductor and the output bank are the same across all three. The second question is whether 6 A is available at 18 V input. It is, but the duty cycle at 0.6 V out is 3 per cent, and the minimum on time of the control scheme becomes the limit, so the frequency folds back and the ripple grows at the bottom of the output range.
The third question is about thermals in the 3 mm by 2 mm body. At 6 A from 12 V to 1.0 V the low side FET carries about 0.9 of the period and dissipates roughly 0.6 W, and the thermal pad has to be stitched into a copper plane rather than a short stub.