Contact Us

TPS56528DDAR

Brand: Texas Instruments
Texas Instruments TPS56528DDAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS56528DDAR — Power Management & Signal Chain | Superb Automation

TPS56528DDAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS56528DDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS56528DDAR: 4.5 V to 18 V input, 5 A synchronous buck converter with Eco-mode

TPS56528DDAR is a D-CAP2 synchronous step-down converter with auto-skip at light load and a fixed 1 ms soft start in a SO PowerPAD (DDA) body of 8 pins. It takes 4.5 V to 18 V in, delivers 5 A through 68 milliohm and 37 milliohm FETs, and switches at 650 kHz with a control loop that needs no external compensation.

Order code and package

Ordering stringTPS56528DDAR, DDA package, 8-pin SO PowerPAD, tape and reel
Package8-pin SO PowerPAD, 3.9 mm by 4.9 mm body with exposed pad
Ambient rangeJunction -40 C to 150 C
Pin count checkEN, VFB, VREG5, PG, GND, SW, VBST and VIN, all eight used
Output range0.6 V to 7 V, set by the feedback divider
Light load modeAdvanced Eco-mode auto-skip, which can be disabled by pulling a pin

Electrical parameters that decide the application

Input range4.5 V to 18 V
Output current5 A continuous
Switch resistance68 milliohm high side, 37 milliohm low side, at 25 C
Reference0.6 V nominal, 1 percent at 25 C
Switching frequency650 kHz nominal, adaptive across line and load
Shutdown currentUnder 10 microamp
Soft startFixed 1 ms internal ramp
ProtectionsCycle by cycle current limit, over voltage at 125 percent of reference, under voltage hiccup at 65 percent, thermal shutdown
Minimum off time260 ns typical, 310 ns maximum

Points to check before this part goes on a BOM

The 5 A rating and a 37 milliohm low-side FET put 0.93 W into the package at full load in continuous conduction, and the thermal pad of an SO PowerPAD is the only way out. That is the number that decides whether the part reaches 5 A: the silicon is rated for it, and a board with 25 square millimetres of copper under the pad is not. The data sheet's efficiency curves are taken on an evaluation board with more copper than a production board usually gets.

Adaptive on time means the frequency moves with the operating point, from roughly 500 kHz at 18 V in to above 750 kHz at 5 V in. Conductive emissions therefore have to be filtered across that band, and an input filter tuned to a single notch at 650 kHz will be ineffective at the ends of the range. That is the same behaviour the 2 A member of the family shows, and it is a property of D-CAP2 rather than a defect.

Eco-mode is what produces the light load efficiency, and it is also what makes the output ripple at 10 mA load larger than at 5 A. In skip mode the converter delivers bursts of energy and the output capacitor absorbs the difference, so the ripple is set by the hysteresis band and the capacitance, not by the 650 kHz clock. A rail that feeds a low noise analogue block should be run in forced continuous mode, and the price is the standby current of a continuously switching converter.

The fixed 1 ms soft start is short for a load with a large capacitance, and there is no pin to slow it down: the eight pins are EN, VFB, VREG5, PG, GND, SW, VBST and VIN. A 1000 microfarad load charged to 1.2 V in 1 ms needs 1.2 A of average charging current, which is fine at 5 A, but a 4700 microfarad load needs 5.6 A and the converter will hit its current limit and stretch the ramp instead of following the 1 ms profile. Where a slower ramp is required the answer is external, a series FET or a separate hot-swap part.

Under voltage hiccup trips at 65 percent of the reference and restarts after seven cycles of delay, so a load step that pulls the rail to 0.4 V produces a full restart rather than a recovery. In a system with a large motor or a hot-plug connector that is the intended behaviour, and in a system with a fast transient load it is a reason to add output capacitance until the rail no longer crosses the threshold.

The 0.6 V reference allows a 1.0 V rail with a divider ratio of 1.67, and the divider current can be kept under 20 microamp with a 100 kohm total. The feedback pin bias current is small, so the divider error is dominated by the resistor tolerance, and 1 percent parts give roughly 2 percent of output error with the reference included. A rail that needs 1 percent total has to start from 0.1 percent resistors.

Where this order code fits

It is used in digital television power supplies, set top boxes, Blu-ray players, network terminals and any 12 V board that needs a 5 A rail with low standby current and a small external component count. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Does it need external compensation? No. D-CAP2 sets the loop internally and the part is stable with ceramic output capacitors across the range, which is why the package has eight pins.

What is the difference from the 2 A family member? Lower resistance FETs, a 5 A rating and a different thermal body, but the same control scheme, so the behaviour at light load and the transient response are similar.

Can the output be 5 V from a 5 V input? No. The converter needs headroom for the high-side FET and the minimum off time, so the output has to stay below the input by more than the dropout at the load current.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.