TPS564201DDCR
Product Specifications
TPS564201DDCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS564201DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS564201DDCR: 4.5 V to 17 V input, 4 A synchronous buck in a 6 pin SOT-23 body
TPS564201DDCR is a fixed frequency synchronous step down converter that integrates both power FETs and needs no external compensation network in a SOT-23 thin body of 6 pins. It runs from 4.5 V to 17 V and holds an output between 0.76 V and 7 V, with 4 A of continuous load current from a body only 1.6 mm by 2.9 mm. The vendor quotes 560 kHz switching, a 1.0 ms fixed soft start and 50 milliohm on the high side FET against 22 milliohm on the low side.
Order code and package
| TPS564201DDCR | 6 pin SOT-23 thin (DDC), 1.60 mm by 2.90 mm, 3000 pieces on a large reel |
| TPS564201DDCT | same body and silicon, 250 pieces on a small reel, the prototype quantity |
| Feedback threshold | 745 mV minimum, 760 mV typical, 775 mV maximum over the full temperature range |
| On resistance | 50 milliohm high side at 25 C with 5.5 V between BST and SW, 22 milliohm low side |
| Operating junction temperature | minus 40 C to plus 125 C, no ambient derating row in the document |
Electrical parameters that decide the application
| Input voltage range | 4.5 V to 17 V, with the enable pin rated to the same 17 V |
| Output voltage range | 0.76 V to 7 V, set by the divider on the VFB pin |
| Continuous output current | 4 A, limited by the cycle by cycle valley current limit |
| Switching frequency | 560 kHz fixed, no resistor to change it |
| Feedback accuracy | 1.6 per cent at 25 C, the window is 745 to 775 mV over temperature |
| Quiescent current | 400 uA typical, 510 uA maximum, measured with the output not switching |
| Shutdown current | 0.9 uA typical, 5 uA maximum with the enable pin pulled low |
| Enable thresholds | 1.6 V high, 0.8 V low, with a 225 to 900 kOhm internal pull down |
| Soft start | 1.0 ms fixed ramp, no capacitor to size |
What the family adds above and below this row
| D-CAP2 control | no external compensation, stable with low ESR polymer and ceramic output capacitors |
| Pulse skip at light load | the part drops cycles rather than holding continuous conduction, which is how the 400 uA quiescent current is reached |
| Pre-biased start | the output can already sit at a voltage when the enable pin goes high, the part does not pull it down first |
| Overcurrent behaviour | cycle by cycle limit first, then hiccup mode if the fault holds, so a shorted rail does not cook the FET |
| Undervoltage and thermal | both are non latching, the part restarts when the condition clears |
| VREG5 pin | an internal 5 V rail brought out for the gate drive, it needs its own 1 uF capacitor and cannot feed a load |
Points to check before this part goes on a BOM
The 4 A figure belongs to the valley current limit and not to a thermal promise. On a 6 pin SOT-23 body the copper under the part decides how much of that 4 A survives a 40 C ambient, and the datasheet thermal table is measured on a JEDEC board with two ounces of copper. A program that needs 4 A continuously at 85 C ambient is looking at a different package, and the same silicon exists in larger bodies for exactly that reason.
The 560 kHz switching frequency is fixed, which removes one decision and one resistor at the same time. It also fixes the inductor ripple at a given inductance, so the 1.5 uH to 2.2 uH range in the vendor application circuit is not a menu of preferences. A larger inductor lowers ripple and slows the transient, a smaller one does the reverse, and D-CAP2 tolerates either because the loop is not compensated by the customer.
The feedback threshold sits at 760 mV typical and the divider is the only thing that sets the rail. That is low enough that the divider current can be a real load on a 1 V rail, and high enough that noise on the VFB trace shows up as output error. The vendor application notes put the divider close to the pin and route it away from the switch node, which is ordinary practice for any low reference converter.
The quiescent current of 400 uA is a switching supply figure and not a standby figure. It applies while the part is enabled and regulating with no load, and pulse skip mode is what keeps it there. A battery product that needs microamps between bursts has to look at the shutdown row instead, where 0.9 uA typical applies as soon as the enable pin is low.
The soft start is fixed at 1.0 ms, so inrush into a large output capacitor is bounded by the part rather than by a capacitor the customer adds. With 4 A available, 1.0 ms is enough to charge a few hundred microfarads without hitting the current limit, and a rail with more capacitance than that will start in current limit and reach the set point later than 1.0 ms. That is worth checking on a rail with a big bulk capacitor downstream.
Hiccup mode is the difference between a converter that survives a short and one that does not. When the current limit trips the part shuts down, waits, and retries, so the average dissipation during a hard fault stays low. The same behaviour means a rail that trips on a transient looks dead on a scope, and the first thing to check is the load step, not the converter.
The enable pin carries an internal pull down between 225 kOhm and 900 kOhm, which is wide enough that an engineer cannot rely on it as a defined logic load. Driving the pin from an open drain output works, but leaving it floating is not the same as tying it low, and the pin is rated to the full 17 V input so it can be tied to VIN directly on an always on rail.
Where this order code fits
The part sits in consumer and networking supplies: digital television rails, set top boxes, home gateways and surveillance recorders, where a 12 V adapter has to become 5 V or 3.3 V at a few amps on a board with very little height. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
Can this part take 17 V in and still hold 4 A out? The input rating allows 17 V and the current limit allows 4 A, but the two together at 560 kHz put the whole loss in a 6 pin body. The vendor curves show the safe load falling with ambient, so a 17 V to 5 V rail at 4 A needs the thermal numbers worked through rather than assumed.
Is an external compensation network needed? No. D-CAP2 is a fixed on time loop with internal compensation, which is why the pin count is six and why the output capacitor ESR becomes part of the loop response. Ceramic and polymer capacitors are both supported.
What is the difference between the R and the T suffix? Reel size only. DDCR ships 3000 pieces on a large reel, DDCT ships 250 pieces on a small reel, and the silicon and the body are the same.
Does the part need a bootstrap capacitor? Yes, one capacitor between BST and SW, 0.1 uF in the vendor circuit. Without it the high side FET has no gate drive and the output collapses under load.
What happens on a shorted output? The valley current limit acts cycle by cycle, then the part enters hiccup and retries. It recovers on its own once the short is removed, with no latch to reset.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.