TPS563210DDFR
Product Specifications
TPS563210DDFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS563210DDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS563210DDFR: 3 A synchronous buck, 4.5 V to 17 V input, 650 kHz, Eco-mode, 8-pin SOT-23
TPS563210DDFR is a 3 A synchronous step down converter with both switches inside an eight pin SOT-23 body that carries a power good output as well as the usual enable and feedback pins in a SOT-23-8 body of 8 pins. The switches measure 68 milliohm on the high side and 39 milliohm on the low side at 25 degrees, which is the lowest pair in this family and the reason the eight pin body can hold 3 A. Control is D-CAP2 with no external compensation, the switching frequency is 650 kHz, and the feedback threshold is 765 mV typical with one per cent accuracy at 25 degrees. Shutdown current is under 10 microamp and the part starts into a prebiased output without discharging it.
Order code and package
| TPS563210DDFR | the 3 A member in the SOT-23-THIN (DDF) body, 8 pins, 3000 pieces on a large reel; the current addendum prints this family with the A suffix as TPS563210ADDFR, marking 3210A |
| TPS562210ADDFR | the 2 A member, 133 and 80 milliohm switches, same body and same pin out |
| Reel options | 3000 pieces on a large reel for the R ending, 250 on a small reel for the T ending |
| Temperature range | minus 40 to 85 degrees ambient, which is narrower than the rest of this family |
| Power good | open drain output that reports the output as valid, brought out on the eighth pin |
Electrical parameters that decide the application
| Input voltage | 4.5 V to 17 V |
| Output voltage | 0.76 V to 7 V, set by a divider into the VFB pin |
| Output current | 3 A continuous |
| Switch resistance | 68 milliohm high side, 39 milliohm low side at 25 degrees |
| Switching frequency | 650 kHz fixed |
| Feedback threshold | 765 mV typical, 751 to 779 mV over minus 40 to 85 degrees |
| Supply current | 190 microamp typical, 290 maximum, not switching; 3 to 10 microamp in shutdown |
| Current limit | 3.5 A minimum, 4.2 A typical, 5.3 A maximum for the 3 A member |
Family variants and how they differ
| TPS563210 | 3 A, the string on this page |
| TPS562210 | 2 A member with 133 and 80 milliohm switches, 2.5 to 4.3 A current limit |
| TPS563200 | an older six pin member of the same family without the power good output |
| Thermal shutdown | 155 degrees with 35 degrees of hysteresis |
| Protection | cycle by cycle current limit, hiccup on undervoltage, non latching overvoltage, undervoltage lockout and thermal shutdown |
Points to check before this part goes on a BOM
The temperature range is the narrowest point of this part. The orderable rows are published at minus 40 to 85 degrees ambient, not the 125 degree junction used elsewhere in the family. A rail inside a sealed enclosure that reaches 85 degrees ambient has no margin left, and the junction will be higher still. For an industrial product running hot, the 125 degree members of the same family are the right choice even though the silicon is similar.
The A suffix in the current addendum is not cosmetic. The document that covers this family now prints the orderable strings with an A, and the electrical table names TPS563210A when it quotes the switch resistance and the current limit. A page that quotes the non-A string from an older catalogue can be sourced, but the offer has to say which revision is shipping, because a customer qualifying a board against the older document will compare the wrong numbers.
Eight pins buy a power good signal and lose nothing. The power good output lets a sequencer or a supervisor know the rail is valid instead of waiting a fixed delay. It is open drain, so it needs a pull up to a rail that is alive before this converter starts, which is usually the standby supply. On a board with three rails that is the difference between a defined start order and a race.
Sixty eight milliohms on the high side is what makes 3 A possible in this body. At 3 A and a 40 per cent duty cycle the high side conduction loss is about 0.24 W and the low side contributes about 0.21 W. That has to leave through the lead frame of an eight pin SOT-23 package, so the copper under and around the part is the thermal solution. A board with a pour and vias carries it; a board with narrow traces folds back at a load it was rated for.
The current limit is above the rating and the minimum point matters. The window is 3.5 A to 5.3 A, so the converter holds 3 A with ripple on top and does not fold back early. A short pulls the current to the limit and the hiccup circuit takes over, switching for a short window and pausing. A fixture that measures the output during a fault reads a pulsing voltage, which is normal behaviour rather than a fault in the part.
A 17 V ceiling covers a 12 V bus and not a 24 V bus. A 12 V rail at plus 10 per cent is 13.2 V and an industrial transient rarely passes 16 V. A 24 V bus is above the rating before tolerance, and a vehicle rail with load dump is far outside it. This is the most common wrong quote on the family: the string looks like an industrial part and is a consumer and telecom part.
The feedback window is wider than the front page suggests. One per cent at 25 degrees becomes 751 to 779 mV across the full range, about 3.7 per cent end to end, before the divider tolerance is counted. A rail that has to hold a tight window at temperature needs 0.1 per cent resistors and a check of the reference drift, not just a tighter divider ratio.
Eco-mode is a light load behaviour and it changes the ripple. Below roughly 200 mA the converter skips pulses, so the switching frequency falls and the output ripple becomes a low frequency wave rather than a 650 kHz triangle. That is fine for a digital rail and wrong for a rail feeding an analogue front end, where the low frequency component sits inside the band of interest. A forced continuous member of the family is the answer for that load.
A 250 piece small reel is not always available on the exact string. The T ending carries 250 pieces and the R ending 3000, and the two are the same silicon on different reels. A prototype build of 300 pieces therefore needs either two small reels or a broken large reel, and that has to be agreed with the supplier before the order is placed rather than discovered at packing.
What to confirm before this part goes on a purchase order
State the input bus, the output voltage and the ambient temperature. The temperature range on this string is 85 degrees ambient and a hot enclosure needs the 125 degree members of the family instead.
Ask which revision is shipping, the plain string or the A revision, and get the date code on the offer. The two are electrically close and the documentation differs, which matters to a customer qualifying the board.
Where this order code fits
It makes a 1.2 V or 5 V rail at 3 A from a 12 V adapter in a network appliance or a display board, on a board that also needs a power good signal to sequence the next rail. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Can it run from a 5 V rail? Yes, 5 V is inside the 4.5 V to 17 V range, but the duty cycle for a 3.3 V output is 66 per cent and the headroom at full load is thin. A 5 V to 1.2 V rail is comfortable. A 5 V to 5 V rail is not possible at all, because there is no boost capability.
What does the power good pin report? It reports the output as valid once the feedback pin is inside its window and the part has finished its soft start. It is open drain and needs a pull up, and it goes low again if the output falls out of regulation, which is what a sequencer uses to hold the next rail off.
Does it need an external compensation network? No. D-CAP2 is compensated internally and there is no COMP pin. The output capacitor is part of the loop, so its value after bias derating has to stay inside the range the application section gives, and a much larger capacitor changes the transient response.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.