TPS563209DDCR
Product Specifications
TPS563209DDCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS563209DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS563209DDCR: 4.5 V to 17 V input, 3 A synchronous buck in SOT-23
TPS563209DDCR is a synchronous step-down converter with both switches inside a six-pin package in a SOT-23 body of 6 pins. It converts 4.5 V to 17 V down to anything from 0.76 V to 7 V at up to 3 A, switches at 650 kHz, and needs no compensation parts because the loop is set inside the device.
Order code and package
| Ordering string | TPS563209DDCR, DDC package, SOT-23, tape and reel |
| Family split | TPS562209 is the 2 A member, TPS563209 the 3 A member, same pinout |
| Package | 6-pin SOT-23, no exposed pad |
| Ambient range | -40 C to 85 C |
| Pin count check | VIN, SW, GND, VFB, EN and VBST, all six used |
Electrical parameters that decide the application
| Input range | 4.5 V to 17 V |
| Current | 3 A rated, current limit 2.5 A minimum, 3.2 A typical, 4.3 A maximum |
| Switch resistance | 122 milliohm high side and 72 milliohm low side in this family |
| Switching frequency | 650 kHz fixed |
| Output range | 0.76 V to 7 V by a divider on VFB |
| Shutdown current | Below 10 microamp |
| Control | D-CAP2, no external compensation |
Points to check before this part goes on a BOM
The rated current and the minimum current limit cross over in the wrong direction. At 12 V in and 1.05 V out with a 2.2 microhenry inductor the ripple is about 0.70 A peak to peak, so a 3 A DC load peaks at 3.35 A, which is above the 2.5 A minimum limit: the part can trip below its own rating. Either the inductor is increased, the input voltage is reduced, or the usable current is set by the limit and not by the front page.
Conduction loss in this package is the second constraint. At 3 A with 122 milliohm on the high side for 8.8 percent of the period and 72 milliohm on the low side for the rest, the switches dissipate about 1.1 W, and this is a SOT-23 with no exposed pad. At 2 A the same arithmetic gives about 0.49 W, which is the number that matches a realistic copper area and a real ambient.
Seventeen volts is the recommended maximum and it is not far above a 15 V rail at plus ten percent, which is 16.5 V. The input capacitor voltage rating has to be 25 V to survive transients that the converter itself will tolerate, so the passive next to the pin is chosen more conservatively than the silicon.
The 0.76 V floor matters for core rails. A 0.9 V core supply from a 12 V input is a 7.5 percent duty cycle at 650 kHz, which is 115 ns of on time, and one percent divider resistors put the setpoint within about 10 mV before the internal reference tolerance is counted. A 0.75 V setpoint is outside the specified output range.
Shutdown current below 10 microamp is 87.6 mAh over a year at the maximum, so a rail that is off for most of its life still has a measurable cost, and the enable pin has to be driven low rather than left floating. The same pin is the only way to sequence this rail against the one that feeds it.
Because both switches are inside a six-pin package, the switch node is the only heat path through the pins and there is no pad to solder. A board that runs 3 A continuously from 12 V needs copper on the SW and GND pins plus airflow, and a board that runs it in a sealed box is better served by the 2 A member of the same family at a lower current.
The bootstrap capacitor between VBST and SW is the one part most often left off a small board. Without it the high-side switch has no gate supply above the switch node, so the converter starts, runs for a moment and stops with the output at zero and no sign of damage, which is easily mistaken for a dead part and leads to the whole converter being replaced when a capacitor of a few nanofarad was all that was missing from the assembly. A 25 V rated part is the norm in this position even though the converter stops at 17 V, because the rail it sits on is allowed to ring above its nominal value and the capacitor, not the silicon, is what fails when it does.
Where this order code fits
The typical fit is a 12 V rail feeding a 1.8 V, 2.5 V or 3.3 V rail at 1 A to 3 A in a small enclosure, where the board area does not allow an exposed pad or a compensation network. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Is this a drop-in for the 2 A member of the family? The pinout and the external parts are the same, so the 3 A part can serve a 2 A socket with the same inductor and capacitors. Going the other way is only safe if the load is below 2 A and the ripple still keeps the peak under the lower current limit.
Why does the output sag on a load step? The loop relies on the output capacitor and its ESR for the transient, so a smaller case size with the same capacitance gives a deeper dip. This is a capacitor selection question before it is a converter question.
Can it run from a 5 V rail? Yes, and that is where the efficiency is best, because the duty cycle is longer and the high-side switch conducts a larger share at lower loss per amp than at 12 V in.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.