Contact Us

TPS563208DDCT

Brand: Texas Instruments
Texas Instruments TPS563208DDCT is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS563208DDCT — Power Management & Signal Chain | Superb Automation

TPS563208DDCT

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS563208DDCT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS563208DDCT 3 A buck in continuous conduction for a clean light load ripple

The TPS563208DDCT is a 4.5 V to 17 V, 3 A synchronous buck in a 6 pin SOT-23, 1.6 mm by 2.9 mm, with 95 milliohm high side and 57 milliohm low side FETs. It shares its document, its pinout and its control scheme with the TPS563201, and the single difference is what happens at light load: this part stays in continuous conduction while its sibling skips pulses.

That choice sets the applications apart. A rail that feeds a comparator, an ADC reference or a small signal chain needs a steady ripple and does not care about a few milliamps of quiescent current. A rail that sleeps for months needs the pulse skipping. Both parts are 3 A, both run at 580 kHz, both have a 0.76 V to 7 V output range and 2 per cent feedback accuracy at 25 degrees.

Soft start is fixed at 1.0 ms, shutdown current is below 20 microamp, and the protection set is cycle by cycle overcurrent with hiccup on a sustained fault, plus non latching undervoltage and thermal shutdown. Junction range is 40 to 125 degrees, and the part starts into a prebiased output.

Key parameters from the SLVSD90B document

Input range4.5 V to 17 V
Output current3 A continuous with 95 milliohm high side and 57 milliohm low side FETs
Output voltage0.76 V to 7 V, set by the feedback divider
Switching frequency580 kHz fixed
Light loadContinuous conduction mode, against pulse skip on the TPS563201
Reference accuracy2 per cent feedback voltage accuracy at 25 degrees
Shutdown currentBelow 20 microamp with the enable pin low
Soft startFixed at 1.0 ms
Package6 pin SOT-23, 1.6 mm by 2.9 mm, DDC body, junction range 40 to 125 degrees

Continuous conduction as a feature

In continuous conduction the inductor current never reaches zero, so the switch node keeps a regular pattern at any load and the output ripple stays at a predictable amplitude. A pulse skipping part, by contrast, delivers bursts of energy and lets the output sag between them. On a rail feeding an analog front end, that burst pattern shows up as noise at the switching frequency divided by the skip ratio, and it lands in the band the front end cares about.

The cost is efficiency at light load. A 3 A converter idling at 1 mA will draw several milliamps in continuous conduction, and the same board with the pulse skipping sibling draws a fraction of that. Choosing between them is a matter of which number the product is measured on: standby current or output noise.

Two siblings, one footprint

Because the two parts share the body and the pinout, a board can be built with either, and the choice can be deferred until the noise measurement is done. The labels differ, so a mixed carton is the risk, and a line that assumes pulse skipping will find out at the emissions test rather than at goods inwards. On a first order of this family, ask for the reel label to be photographed.

Everything else is common: the same inductor table for a given output voltage, the same output capacitor recommendation, the same divider equation, and the same fixed 1.0 ms soft start, which is short enough that a large output bank will show inrush current on the upstream supply at every power up.

Where this part fits

3 A rails on industrial control boards, analog front ends, instrumentation and any board where the light load ripple has to stay small. Our desk keeps the second source notes and the sibling comparison, see power management cross reference and how to verify a drop in replacement.

What to check before a purchase order

The DDC suffix is the 6 pin SOT-23 at 1.6 by 2.9 mm, and the smaller SOT563 body used by other 3 A devices does not fit the same pads. The order code ends in 208 for this part and 201 for the pulse skipping sibling, and the difference is a single digit on a reel label. Confirm which one the bill actually specifies before the line starts.

See incoming inspection plan for the marking check, and component lead time solutions when one sibling is short and the other is not.

Questions that come up on this part

Can the pulse skipping part be used in place of this one, is the usual question. It fits and it regulates, but the light load ripple changes and any emissions result taken on this part has to be repeated. The second question is whether 20 microamp shutdown includes the input divider. It does not, so a board with a permanent divider across the input draws more than the figure in the document.