Contact Us

TPS563208DDCR

Brand: Texas Instruments
Texas Instruments TPS563208DDCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS563208DDCR — Power Management & Signal Chain | Superb Automation

TPS563208DDCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS563208DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS563208DDCR: 4.5 V to 17 V input, 3 A synchronous step-down, continuous conduction mode, SOT-23-6

TPS563208DDCR is a synchronous step-down converter rated 3 A that runs in continuous conduction mode at a fixed switching frequency across the whole load range in a SOT-23 body of 6 pins. This is the forced continuous member of a two part family. Where the other member skips pulses at light load for efficiency, this one keeps switching, so the ripple and the switching spectrum do not change with the load. That is the right behaviour for a board that is scanned for emissions at several load points and for a rail that feeds a sensitive load at light current.

Order code and package

TPS563208DDCRActive, SOT-23-6 thin, 3000 pieces on a large reel, SN finish, MSL-1-260C unlimited floor life, marking 3208
TPS563208DDCTActive, 250 pieces on a small reel, the same body
TPS563201the pulse skip member of the family, same body and pinout, different light load behaviour
Package size1.6 mm by 2.9 mm including pins, six pin SOT-23 thin
Junction rangeminus 40 to 125 degrees on the published rows

Electrical parameters that decide the application

Input voltage4.5 V to 17 V
Output current3 A continuous
Output voltage0.76 V to 7 V, set by an external divider
Switch resistance95 milliohm high side, 57 milliohm low side
Switching frequency580 kHz fixed
Feedback accuracy2 per cent at 25 degrees
Soft start1.0 ms fixed, internal
Shutdown currentless than 20 microamp

Family variants and how they differ

TPS563208forced continuous conduction, the string on this page
TPS563201pulse skip at light load, higher efficiency at a few milliamp
ControlD-CAP2 adaptive on time with no external compensation
Protectioncycle by cycle current limit, hiccup overcurrent, non latching undervoltage and thermal shutdown
Start upworks into a pre biased output without discharging it

Points to check before this part goes on a BOM

Continuous conduction is a choice that costs light load efficiency. The converter keeps the low side switch on for part of each cycle even when the inductor current would otherwise reach zero, so at a few milliamp the losses are higher than a pulse skipping part. The return is a ripple and a spectrum that do not move with the load, which is what an emissions scan and a sensitive analogue load both need.

Two per cent feedback accuracy is loose for this class. Most converters in the same body quote 1 per cent at room temperature. Two per cent means a 3.3 V rail can sit at 3.37 V before any divider tolerance is added. A board that needs a tight rail should either use the divider to trim or choose a part with a tighter reference, and the number has to be on the error budget rather than discovered at test.

Five hundred and eighty kilohertz is the frequency to check against the emissions plan. It is not a round number, and a scan that starts at 500 kHz will see the fundamental and its harmonics across the band of interest. This part has no spread spectrum, so the energy sits at one frequency; the input filter has to be chosen for that frequency rather than for a smeared spectrum.

A one millisecond soft start is short for a 3 A part. It charges the output capacitor fast enough that a large bank will hit the current limit at power up. The limit is cycle by cycle and hiccup mode follows if it persists, so the rail comes up but the input supply sees a pulse of current. On a weak adapter that pulse can brown out the rest of the board.

Hiccup overcurrent behaves differently from a foldback. The part shuts down, waits internally, and restarts. A shorted output therefore shows as a pulsing rail rather than a low voltage. That is easier on the part and harder on a test fixture, and it means a fault on the load can look like an unstable supply on a scope.

The marking 3208 is the whole identification. The 3 A pulse skip member and this one share a body, a pinout and almost the same marking. A board that was qualified with continuous conduction and repaired with the pulse skip member will pass a functional test and fail an emissions test, and the difference is invisible without the reel label.

Thermal performance sets the real current at 17 V in. At 17 V in and 5 V out the high side carries a short duty cycle but switches at 17 V, so the switching loss is significant. Three amps is available on a board with copper under the part and less on a two layer board with a narrow trace into the switch node.

The enable pin is a precision input. It can be used with a divider from the input as an adjustable undervoltage lockout, which is how a board avoids starting while the bus is still ramping. A simple logic drive works too, but the threshold is tight enough that a slow rising input can hold the part in an undefined state part way through the ramp.

This family has no output overvoltage protection. A fault that drives the high side switch on continuously is not detected by the converter. On a rail that feeds a 5 V load from 17 V that is a real risk, and a clamp or a supervisor with an overvoltage output is worth the space.

What to confirm before this part goes on a purchase order

Confirm which member of the family the board was qualified with. The pulse skip and the continuous conduction parts share a body and a pinout and behave differently at light load.

Ask for the date code and the reel label with the marking 3208, and confirm whether the quantity is a full reel or a break. At 3000 pieces per reel, a small order has to be agreed with the packaging stated on the offer.

The output voltage is set by a divider on the board, so the same string appears at several rails. A substitute can only be checked against the actual output and load, and the divider values belong on the enquiry together with the input bus. A rail that carries a light load at 5 V has very different margin from the same rail at 1.2 V, and the divider values are what tell the two apart. Ask for them with the enquiry so the part can be matched to the rail it will actually feed.

Where this order code fits

It runs a 3 A rail at a fixed frequency in a surveillance or set top box board, where the continuous conduction mode keeps the switching spectrum predictable at light load. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

What is the difference from the TPS563201? The light load behaviour. This part keeps switching in continuous conduction across the load range, so the ripple and the spectrum stay the same; the 563201 skips pulses for efficiency at light load and changes both.

Does it need a bootstrap capacitor? Yes, one small capacitor between the switch node and the boost pin. It is the only part of the gate drive outside the package.

Can it deliver 3 A at 17 V input? The current rating is electrical. At 17 V the switching loss in the high side switch is the limit, and the junction temperature on the real board decides whether 3 A is available continuously.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.