Contact Us

TPS563202DRLR

Brand: Texas Instruments
Texas Instruments TPS563202DRLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS563202DRLR — Power Management & Signal Chain | Superb Automation

TPS563202DRLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS563202DRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS563202DRLR: 3 A synchronous buck converter from 4.3 V to 17 V in a SOT563 package

TPS563202DRLR is a 3 A synchronous buck converter in a six pin SOT563 body that needs no external compensation and holds a 580 kHz switching frequency in a SOT563 body of 6 pins. The TPS563202 takes 4.3 V to 17 V in and delivers 3 A with a 95 mOhm high side and a 57 mOhm low side switch inside a SOT563 package. The control loop is internally compensated and stable with ceramic output capacitors, so the external parts are an inductor, two capacitors and the feedback divider. Switching is fixed at 580 kHz, the reference is 806 mV, soft start is 1.2 ms, and the part drops into eco-mode at light load. Quiescent current is 380 uA typical and shutdown current is 1 uA.

Order code and package

Order codeTPS563202DRLR
Input voltage4.3 V to 17 V
Output current3 A
Output voltage0.806 V to 7 V, set by a divider
Integrated switcheshigh side 95 mOhm, low side 57 mOhm
Controlinternally compensated, stable with ceramic output capacitors
Switching frequency580 kHz typical
Feedback voltage806 mV typical in continuous conduction
Soft-start time1.2 ms, 10 percent to 90 percent of the output
Package6 pin SOT563
Quiescent current380 uA typical
DocumentD-CAP2 family data sheet for the TPS563202

Electrical parameters that decide the application

Valley current limit3.3 A minimum, 4.4 A typical, 5.6 A maximum
Shutdown current1 uA typical, 3 uA maximum
Enable high threshold1.35 V minimum, 1.6 V maximum
Enable low threshold0.8 V maximum, 1.05 V minimum
Enable pin resistance225 kOhm minimum, 400 kOhm typical, 900 kOhm maximum to ground
Input UVLO3.3 V minimum falling, 3.6 V maximum, 0.4 V hysteresis
Wake-up input voltage4.0 V minimum, 4.3 V maximum
Output undervoltage protectionhiccup at 65 percent of nominal
Junction range-40 C to 125 C
Feedback accuracy2 percent at 25 C
Eco-mode threshold815 mV on the feedback pin
Thermal paththe six pin body soldered to the copper pour

Points to check before this part goes on a BOM

The valley current limit is what protects this part, and its minimum of 3.3 A sets the real ceiling on a 3 A rail. At 3 A with a 30 percent ripple the valley sits at about 2.55 A, so the margin is there, but a board with a small inductor that runs 60 percent ripple would put the valley close to the minimum limit and could trip early at high temperature.

No external compensation is the reason a six pin package is possible. The loop is fixed internally for a ceramic output capacitor range, so the choice of output capacitor is not free: an electrolytic with a large equivalent series resistance moves the loop and can produce a response the part was not characterised for. The document is explicit that the part supports low equivalent series resistance capacitors, ceramic and specialty polymer.

Eco-mode holds the output slightly high at light load. The feedback threshold in that mode is 815 mV against 806 mV in continuous conduction, so the rail sits about one percent above nominal when the load is a few milliamps. On a rail that feeds a standby processor this is harmless; on a rail that is measured at no load it looks like a tolerance failure.

The 580 kHz frequency is a compromise between inductor size and switching loss, and it sits below the AM band. That matters for a board that also carries an analog front end: a converter at 580 kHz puts its second and third harmonics in the medium wave band, where a ferrite bead and a small input capacitor are usually enough to keep them out of a signal path.

Soft start is fixed at 1.2 ms with no pin to change it. A board with a large output capacitance, for example 470 uF of polymer, will draw a start-up current that the current limit clamps, and the output then ramps at a rate set by the limit and the capacitance rather than by the internal timer. That behaviour is safe but slower than the data sheet figure suggests, and a power good chain that expects 1.2 ms has to allow for it.

The enable pin has an internal resistance to ground of 225 kOhm minimum, which means an open enable pin does not reliably turn the part off. A board that relies on a three state driver or an unpopulated resistor to disable the rail should pull the pin down with an explicit resistor, because the internal bias can hold it above the 1.35 V threshold.

Hiccup undervoltage protection at 65 percent of nominal is a behaviour to plan around in a multi rail system. If the 3 A rail is loaded by a device that draws a large inrush, the output dips, the part enters hiccup and the rail cycles until the load stops pulling. Sequencing the load after the rail is established avoids the cycle entirely.

Where this order code fits

This order code fits digital television supplies, smart speakers, wired networking equipment and set top boxes, which is the load profile a 12 V to 5 V or 12 V to 3.3 V rail at 3 A describes. The six pin body and the absence of a compensation network make it a candidate for cost sensitive boards with a short assembly flow. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Does this part need a compensation network? No. The loop is internally compensated, so only the inductor, the input and output capacitors and the feedback divider are external.

What output voltages can it produce? Any voltage between 0.806 V and 7 V that the divider sets, subject to the minimum on time at high input voltage.

Is the 3 A rating continuous? It is the rated load, and the valley current limit at 3.3 A minimum is what actually bounds a board with a large ripple current.

SUPERB supplies this order code with date codes and packing stated, and the How to Reduce Component Cost page sets out how to compare a low pin count buck across vendors before a board is committed.