Contact Us

TPS563201DDCR

Brand: Texas Instruments
Texas Instruments TPS563201DDCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS563201DDCR — Power Management & Signal Chain | Superb Automation

TPS563201DDCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS563201DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS563201DDCR: 4.5 V to 17 V, 3 A synchronous buck in a six pin SOT-23

TPS563201DDCR is a synchronous step down converter with pulse skip at light load and a fixed 580 kHz on time loop in a SOT-23 body of 6 pins. It is the three amp member of the D-CAP2 family in the smallest body TI puts it in, and the pulse skip behaviour is what separates it from the continuous version next to it on the same data sheet.

Order code and package

Order codeTPS563201DDCR, DDC package, 3000 pieces on a large reel
BodySOT-23, 2.9 mm by 1.6 mm, six pins, no exposed pad
Conduction modePulse skip at light load on this suffix, the TPS563208 is the forced continuous version
ControlD-CAP2 adaptive on time with an internal ramp, no external compensation
Reference768 mV typical, 749 mV to 787 mV in continuous mode, 774 mV typical in pulse skip
Output range0.76 V to 7 V, set by two resistors

Electrical parameters that decide the application

Input range4.5 V to 17 V operating, 19 V absolute maximum
Output current3 A continuous, current limit 3.3 A to 5.1 A measured as a DC value at 1.05 V out
High side switch95 mOhm typical at 25 C
Low side switch57 mOhm typical at 25 C
Switching frequency580 kHz nominal, pseudo fixed with input and output
Minimum off time220 ns typical and 310 ns maximum, capping the duty near 82 per cent
Quiescent current120 uA on the pulse skip part and 350 uA on the continuous part, 8 uA to 20 uA shut down
Soft start1.0 ms internal, monotonic into a pre-biased output
Under voltage lockout3.8 V to 4.3 V rising, 3.3 V to 3.4 V falling, 0.4 V of hysteresis
ProtectionCycle by cycle current limit, hiccup with 1.2 ms on and 10 ms off, thermal shutdown at 172 C

Family variants and how they differ

TPS563208the same die in forced continuous mode, 350 uA quiescent and a tighter light load ripple
TPS5622072 A from 17 V in a smaller SOT563 body, continuous only, with a 0.804 V reference
TPS5622122 A from 18 V in an eight pin body with a selectable mode and a power good output
TPS56C23012 A in a 20 pin QFN, for loads the six pin body cannot hold
TPS621303 A from 17 V in a 16 pin QFN with DCS control, when the board wants a QFN rather than a leaded body

Points to check before this part goes on a BOM

Three amps in a SOT-23 is a die rating more than a package rating. At 3 A from 12 V to 5 V the low side switch conducts 58 per cent of the period at 57 mOhm for 0.37 W and the high side 0.24 W at 95 mOhm, so the package sheds about 0.6 W through six leads with no exposed pad. A board that expects 3 A continuously at 60 C inside an enclosure has to give that heat a large copper area on both the SW and the ground pins, and many boards settle at 2 A after a thermal measurement.

The pulse skip behaviour on this suffix is the reason the quiescent current is 120 uA rather than 350 uA. Below the light load threshold the part stops switching, lets the output decay, then bursts again, so the output ripple at no load becomes a sawtooth at a few kilohertz rather than a 580 kHz triangle. Audio and analog rails can hear that, and when they do, the TPS563208 in the same footprint is the answer, at the cost of 230 uA more standing current.

The reference moves with the mode. In continuous conduction the feedback threshold is 768 mV typical with a 749 mV to 787 mV window, and in pulse skip it is 774 mV, about 0.8 per cent higher. That is a deliberate offset so the part does not hunt between modes at the boundary, and it means a rail measured at no load reads slightly high before the load pulls the loop back into continuous operation.

Current limit is quoted as a DC output current rather than a switch valley, 3.3 A minimum and 5.1 A maximum with a 1.5 uH inductor and 1.05 V output. With a 3 A rating the margin to the minimum is only ten per cent, so ripple, inductor tolerance and the tolerance of the sense circuit all sit inside that window. A board that runs at 3 A continuously is at the limit of the specification, and a board at 2.5 A has room for the inductor to saturate a little before the loop limits.

The 4.5 V minimum input and the 3.8 V to 4.3 V lockout are worth reading together, because they rule out a 3.3 V rail entirely. This is a 5 V, 12 V or 15 V part. A 3.3 V input is below the lockout and the part will not start, which is the kind of mistake that shows up only after the divider and the inductor have been chosen for the wrong rail.

Protection has a wide thermal window, 172 C trip with 37 C of hysteresis, which is high for a plastic body and reflects the thermal resistance of the package rather than a tolerance for a hot board. On a fault the part hiccups for 1.2 ms and rests for 10 ms, an eleven per cent duty that keeps the average dissipation low enough for the body to survive until the fault clears or somebody finds it.

The enable pin carries 600 kOhm to 2.4 MOhm to ground and a 1 uA pull down, so a simple resistor to the input works but a high impedance divider does not. The threshold is 1.6 V high and 0.8 V low, which allows the pin to be driven from 3.3 V logic, and the internal pull down is what holds the converter off when the pin is left floating on a board that has not populated the divider.

The bootstrap capacitor is the only external part the loop needs besides the inductor, the output bank and the divider. Because the high side gate drive is referenced to the switch node, a 0.1 uF part between BST and SW at 10 V is enough, and an open joint there produces a converter that switches once at start-up and then stops, with the output sitting at whatever the pre-bias left behind.

The 310 ns maximum off time puts a floor under the input voltage for a given output, the same arithmetic as the rest of the family. 3.3 V needs about 4.0 V in, 1.2 V needs 1.5 V in, and a 5 V to 5 V pass through is impossible. The part is a step down converter with a maximum duty near 82 per cent, not a switch.

Where this order code fits

It belongs on the 5 V or 12 V rail of a digital television, a set top box, a network terminal or a Blu-ray player, where a single 3 A rail feeds a processor core or a memory supply and the board has no room for an external switch pair. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

Can it run from a 3.3 V rail? No. The under voltage lockout is 3.8 V to 4.3 V rising, so 3.3 V never starts the part. The minimum operating input is 4.5 V.

What is the difference from the TPS563208? Only the light load behaviour. This part skips pulses and draws 120 uA at no load, the 208 stays continuous with a 580 kHz ripple and draws 350 uA. The pin out and the rest of the specification are the same.

How much current can it really carry? 3 A is the die rating. The package has to shed about 0.6 W at that current, so the copper area under the part decides what the board can hold at temperature.

What is the smallest output it can regulate from 12 V? About 1.2 V. The 310 ns maximum off time limits duty to 82 per cent, and 1.0 V from 12 V is below that floor.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.