Contact Us

TPS562219DDFR

Brand: Texas Instruments
Texas Instruments TPS562219DDFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS562219DDFR — Power Management & Signal Chain | Superb Automation

TPS562219DDFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS562219DDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS562219DDFR 2 A synchronous buck in an 8 pin SOT-23

The TPS562219DDFR is a 2 A synchronous step down converter in an 8 pin SOT-23, 1.6 mm by 2.9 mm, with 133 milliohm high side and 80 milliohm low side FETs. It takes 4.5 V to 17 V in and delivers 0.76 V to 7 V out at a fixed 650 kHz, using D-CAP2 control that needs no external compensation and works with all ceramic output capacitors. For a 2 A rail on a control board, that is the whole circuit: the converter, an inductor, two capacitors and a feedback divider.

The document covering this order code is the TPS56x219A data sheet, which describes the TPS562219A and the TPS563219A. The A revision is the one the vendor documents, and the plain 219 order codes trace to the same silicon family with the same pinout. Any board that has to be qualified against a current document should be checked against the A revision rows rather than against an older print.

Behaviour worth knowing: the device always operates in continuous conduction mode, so the output ripple at light load stays small compared with a pulse skipping part, at the cost of a higher no load current. The feedback reference is 1 per cent at 25 degrees. Shutdown current is below 10 microamp. Soft start is adjustable, and there is an open drain power good output.

Key parameters from the SLVSDT2 document

Input range4.5 V to 17 V, single rail with no separate bias pin
Output current2 A continuous with 133 milliohm high side and 80 milliohm low side FETs
Output voltage0.76 V to 7 V, set by the feedback divider
Switching frequencyFixed 650 kHz, no timing component needed
Reference accuracy1 per cent feedback voltage accuracy at 25 degrees
Shutdown currentBelow 10 microamp with the enable pin low
ProtectionCycle by cycle overcurrent limit, hiccup mode undervoltage, non latching overvoltage, UVLO and thermal shutdown
Package8 pin SOT-23, 1.6 mm by 2.9 mm, DDF body, specified from 40 to 85 degrees ambient

Continuous conduction at light load, on purpose

Most small bucks skip pulses at light load to save quiescent power, and pay for it with output ripple that can trip a sensitive load. This part stays in continuous conduction, so a 2 A rail feeding a comparator or a reference sees a steady ripple rather than a burst pattern. The trade is no load current: a battery product that sleeps for a year should not use this part, and a mains powered board that needs a clean 1.8 V rail should.

Because the frequency is fixed at 650 kHz and the control needs no compensation, the only variables are the inductor value and the output capacitance. The document gives a table for common output voltages, and a 2.2 microhenry inductor with two 22 microfarad ceramics covers most 1.2 V to 3.3 V cases at 2 A.

Protection and startup

Overcurrent is cycle by cycle, and a sustained fault moves the part into hiccup on the undervoltage path rather than latching. Overvoltage, UVLO and thermal shutdown are all non latching, so a board recovers on its own once the condition clears. For an appliance board inside a sealed enclosure, that behaviour matters more than the exact limit, because a latched rail means a service call.

Soft start is set by a capacitor, and the part starts into a prebiased output without pulling it down. Prebias startup is the case where a 3.3 V rail is already alive through a body diode before the converter enables, and a part that discharges the output first will glitch the whole board.

Where this part fits

2 A rails on set top boxes, routers, industrial control boards, appliance controllers and any board that needs a small, low part count buck with a clean light load ripple. Our desk keeps the second source and the receipt checks for this class, see power management cross reference and one stop BOM sourcing.

What to check before a purchase order

Three fields. The DDF suffix is the 8 pin 1.6 by 2.9 mm SOT-23, and the 6 pin SOT-23 bodies used by other members of the family do not fit the same pads. The order code digit separates the 2 A device from the 3 A device, which shares the document and the pinout. And the revision letter matters, because the vendor documents the A revision and an older print may not carry the current rows.

See incoming inspection plan for how we check small SOT markings, and date code management for how we handle reels of a part that ships in high volume.

Questions that come up on this part

Is the 3 A version a drop in for this one, is the usual question. It shares the document and the pinout, so yes on the pads, but the inductor and the output bank have to carry the extra current. The second question is whether 650 kHz is a problem near an AM band. It can be, and the harmonic that lands there is the fourth, so an input filter is the usual answer rather than a frequency change, since the frequency is fixed.