TPS562219ADDFR
Product Specifications
TPS562219ADDFR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS562219ADDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS562219ADDFR: 4.5 V to 17 V input, 2 A synchronous step-down converter in SOT-23
TPS562219ADDFR is a D-CAP2 synchronous buck converter that needs no external compensation and keeps the output stable with ceramic capacitors in a SOT-23 (DDF) body of 8 pins. It runs from 4.5 V to 17 V, switches at 650 kHz, delivers 2 A from 133 milliohm and 80 milliohm integrated FETs and sets the output anywhere from 0.76 V to 7 V with two resistors.
Order code and package
| Ordering string | TPS562219ADDFR, DDF package, 8-pin SOT-23, tape and reel |
| Family members | TPS562219A (2 A), TPS563219A (3 A, 68 milliohm and 39 milliohm FETs) |
| Package | 8-pin SOT-23, 1.60 mm by 2.90 mm |
| Ambient range | -40 C to 85 C, junction to 150 C |
| Pin count check | GND, SW, VIN, PG, SS, VFB, EN and VBST |
| Output range | 0.76 V to 7 V, set by the feedback divider |
Electrical parameters that decide the application
| Input range | 4.5 V to 17 V, which covers a 12 V bus with tolerance and a 5 V rail |
| Output current | 2 A continuous with the internal FETs |
| Switch resistance | 133 milliohm high side, 80 milliohm low side, at 25 C |
| Reference | 0.765 V nominal, 1 percent at 25 C, 757 mV to 773 mV across the window |
| Switching frequency | 650 kHz nominal, 450 kHz to over 800 kHz across line and load |
| Current limit | 2.5 A minimum, 3.2 A typical, 4.3 A maximum, cycle by cycle |
| Soft start | 6 microamp to 7.8 microamp into the SS capacitor, 4.2 V full scale |
| Protections | Hiccup under voltage, non latching over voltage at 125 percent of reference, thermal shutdown at 155 C |
| Quiescent | 650 microamp to 900 microamp operating, under 10 microamp shutdown |
Points to check before this part goes on a BOM
The 2 A rating and the 2.5 A minimum current limit are close enough that the margin is decided by the inductor, not by the silicon. With a 2.2 microhenry part at 12 V in and 1.05 V out, the ripple is about 0.9 A peak to peak, so a 2 A load peaks at 2.45 A in the switch and sits right on the minimum limit. A 3.3 microhenry part cuts the ripple to 0.6 A and moves the peak to 2.3 A, which is the difference between a converter that holds 2 A and one that folds back under a warm load.
The reference tolerance is quoted as 1 percent at 25 C but the table gives 757 mV to 773 mV, which is plus or minus 1 percent around 765 mV, and the 0 C to 85 C and -40 C to 85 C rows add a further band. On a 1.05 V rail that 16 mV window is 1.5 percent of the output, so a load that needs 2 percent total has no room left for the divider resistors unless they are 0.1 percent parts.
D-CAP2 control removes the compensation network and puts the burden on the output capacitor. The data sheet asks for ceramic or polymer parts with controlled ESR, and the loop is stable across the range without a zero of our own. That is the reason the part has eight pins instead of sixteen, and it is also the reason a cheap electrolytic on the output can produce a slow ringing that no amount of input capacitance fixes.
The 650 kHz switching frequency is not fixed. The characteristics show it falling towards 450 kHz at 17 V in and rising above 800 kHz at 4.5 V in, because the on time is generated adaptively. Filtering for conducted emissions has to be built around the lowest frequency in that band, not the 650 kHz printed on the front page, or the filter will be tuned to a notch that the converter walks away from.
Soft start is set by the capacitor on SS at 6 microamp to 7.8 microamp, so 10 nF gives about 6 ms to reach the 4.2 V full scale and 100 nF gives about 60 ms. In a hot plug case the slower ramp is what keeps the upstream 12 V bus from sagging, and it costs nothing but board area, which makes 100 nF the value to start from when the load has more than 100 microfarad of its own.
The power good output is open drain and switches at 90 percent of the reference on the way up and 85 percent on the way down, with a 7.8 microamp sink. A host that uses PG to release a reset sees about 5 percent of hysteresis, which is enough to stop chatter at the threshold but not enough to hide a real rail collapse, and the pin needs a pull-up to a rail that is alive before the converter starts.
Where this order code fits
It suits a 12 V or 5 V bus that has to produce a 1.2 V, 1.8 V, 3.3 V or 5 V rail for a set top box, a digital television board, a router or a network appliance, where 2 A is enough and the board cannot afford a controller with external FETs. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the One Stop BOM Sourcing page.
Questions buyers ask
Is the 3 A version pin compatible? The TPS563219A is the same 8-pin SOT-23 body with lower resistance FETs and a 3.5 A to 5.3 A current limit, so the board can be built for 2 A and re-populated for 3 A without a change.
Does it start into a pre-biased output? Yes. The converter supports startup with the output already charged, which matters when a second rail or a backup supply holds the node up before the enable pin is released.
What happens on a hard short? The current limit acts cycle by cycle, then the under voltage comparator sees the rail below 65 percent of the reference and the part enters hiccup, retrying after about seven cycles of off time until the short is removed.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.